Nissan Quest E52. Instruction — part 980
PWC-32
< BASIC INSPECTION >
[FRONT WINDOW ANTI-PINCH]
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL
Description
INFOID:0000000009653289
When the battery negative terminal is disconnected, the initialization is necessary for normal operation of
power window system.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000009653290
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
>> END
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW SWITCH
PWC-33
< BASIC INSPECTION >
[FRONT WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW SWITCH
Description
INFOID:0000000009653291
When the power window main switch or front power window switch (passenger side) replaced, the initialization
in necessary for normal operation of power window system.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000009653292
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
>> END
PWC-34
< BASIC INSPECTION >
[FRONT WINDOW ANTI-PINCH]
SYSTEM INITIALIZATION
SYSTEM INITIALIZATION
Description
INFOID:0000000009653293
If any of the following operations are performed, the initialization is necessary for normal operation of power
window system.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch or front power window switch (passenger side) replaced.
• Electric power supply to power window main switch or front power window switch (passenger side) or power
window motor (driver side/passenger side) is interrupted by blown fuse or disconnection and connection of
the negative terminal of battery, etc.
• Disconnection and connection of power window main switch or front power window switch (passenger side)
harness connector.
• Removal of power window motor (driver side/passenger side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000009653294
1.
STEP 1
1.
Turn ignition switch ON.
2.
Operate power window switch to fully open the window. (This operation is unnecessary if the window is
already fully open)
3.
Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed
position, keep pulling the switch for 2 seconds or more.
4.
Check that AUTO-UP function operates normally.
>> GO TO 2.
2.
STEP 2
Check anti-pinch function. Refer to
>> END
CHECK ANTI-PINCH FUNCTION
PWC-35
< BASIC INSPECTION >
[FRONT WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
CHECK ANTI-PINCH FUNCTION
Description
INFOID:0000000009653295
If any of the following operations are performed, the initialization is necessary for normal operation of anti-
pinch function.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch or front power window switch (passenger side) replaced.
• Electric power supply to power window main switch or front power window switch (passenger side) or power
window motor (driver side/passenger side) is interrupted by blown fuse or disconnection and connection of
the negative terminal of battery, etc.
• Disconnection and connection of power window main switch or front power window switch (passenger side)
harness connector.
• Removal of power window motor (driver side/passenger side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
Work Procedure
INFOID:0000000009653296
1.
CHECK ANTI-PINCH FUNCTION
1.
Fully open the door window.
2.
Place a piece of wood near fully closed position.
3.
Close door glass completely with AUTO-UP.
4.
Check the following conditions.
-
Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.
-
Check that glass does not rise not when operating the power window main switch or front power window
switch (passenger side) while lowering.
CAUTION:
•
Perform initial setting when AUTO-UP operation or anti-pinch function does not operate nor-
mally.
•
Check that AUTO-UP operates before inspection when system initialization is performed.
•
Do not check with hands and other body parts because they may be pinched. Do not get
pinched.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст