Nissan Quest E52. Instruction — part 390
DLK-274
< DTC/CIRCUIT DIAGNOSIS >
INTELLIGENT KEY WARNING BUZZER
Component Inspection
INFOID:0000000009649190
1.
CHECK INTELLIGENT KEY WARNING BUZZER
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key warning buzzer connector.
3.
Connect battery power supply directly to Intelligent Key warning buzzer terminals and check the opera-
tion.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key warning buzzer.
Intelligent Key warning buzzer
Operation
Terminal
(+)
(
−
)
1
3
Buzzer sounds
INTELLIGENT KEY
DLK-275
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY
Component Function Check
INFOID:0000000009649191
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key is OK.
NO
>> Refer to
DLK-275, "Component Inspection"
.
Component Inspection
INFOID:0000000009649192
1.
CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA. Refer to
.
Is the measurement value within the specification?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key battery.
Monitor item
Condition
RKE OPE COUN1
Check that the numerical value is changing while operating on the Intelligent Key.
Standard
: Approx. 2.5 - 3.0V
OCC0607D
DLK-276
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION METER BUZZER
COMBINATION METER BUZZER
Component Function Check
INFOID:0000000009649193
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “INSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Touch “Key”, “Knob” or “Take Out” to check that it works normally.
Is the inspection result normal?
Yes
>> Combination meter buzzer is OK.
No
>> Refer to
DLK-276, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009649194
1.
CHECK COMBINATION METER BUZZER CIRCUIT
WCS-40, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
INFORMATION DISPLAY
DLK-277
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INFORMATION DISPLAY
Component Function Check
INFOID:0000000009649195
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “LCD” in “ACTIVE TEST” mode.
3.
Check each warning display on meter display.
Is the inspection result normal?
YES
>> Information display is OK.
NO
>> Refer to
DLK-277, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009649196
1.
CHECK COMBINATION METER
MWI-34, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст