Nissan Quest E52. Instruction — part 26
DOOR MIRROR MOTOR
ADP-97
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror motor.
Door mirror
Operational direction
Terminal
(+)
(-)
10
11
RIGHT
11
10
LEFT
12
10
UP
10
12
DOWN
ADP-98
< DTC/CIRCUIT DIAGNOSIS >
SEAT MEMORY INDICATOR
SEAT MEMORY INDICATOR
Component Function Check
INFOID:0000000009649689
1.
CHECK FUNCTION
1.
Select “MEMORY SW INDCTR” in “Active test” mode with CONSULT.
2.
Check the memory indicator operation.
Is the operation of relevant parts normal?
YES
>> INSPECTION END
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000009649690
1.
CHECK SEAT MEMORY SWITCH INDICATOR OPERATION
Check seat memory switch indicator operation.
Which is the malfunctioning indicator?
All indicators are NG>>GO TO 2.
An indicator is NG>>GO TO 4.
2.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing affected circuit.
3.
CHECK SEAT MEMORY SWITCH INDICATOR POWER SUPPLY
Check voltage between seat memory switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace seat memory switch. Refer to
ADP-113, "Removal and Installation"
.
NO
>> Repair or replace harness between seat memory switch and 10 A fuse [No.10, located in fuse
block (J/B)].
4.
CHECK SEAT MEMORY SWITCH INDICATOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and seat memory switch connector.
3.
Check continuity between driver seat control unit harness connector and seat memory switch harness
connector.
Test item
Description
MEMORY SW INDCTR
OFF
Memory switch indicator
OFF
ON-1
Indicator 1: ON
ON-2
Indicator 2: ON
Signal name
Fuse No.
Battery power supply
10 (10 A)
(+)
(-)
Voltage (V)
Seat memory switch
Connector
Terminals
D13
5
Ground
Battery voltage
SEAT MEMORY INDICATOR
ADP-99
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-111, "Removal and Installation"
NO
>> Repair or replace harness or connector.
Driver seat control unit
Seat memory switch
Continuity
Connector
Terminal
Connector
Terminal
B552
7
D13
7
Existed
23
6
Driver seat control unit
Ground
Continuity
Connector
Terminal
B552
7
Not existed
23
ADP-100
< SYMPTOM DIAGNOSIS >
MANUAL FUNCTION DOES NOT OPERATE
SYMPTOM DIAGNOSIS
MANUAL FUNCTION DOES NOT OPERATE
ALL COMPONENT
ALL COMPONENT : Diagnosis Procedure
INFOID:0000000009649691
1.
CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Check driver seat control unit power supply and ground circuit.
Refer to
ADP-58, "DRIVER SEAT CONTROL UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Check automatic drive positioner control unit power supply and ground circuit.
Refer to
ADP-58, "AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
POWER SEAT
POWER SEAT : Diagnosis Procedure
INFOID:0000000009649692
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
Check power seat switch ground circuit.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
SEAT SLIDING
SEAT SLIDING : Diagnosis Procedure
INFOID:0000000009649693
1.
CHECK SLIDING MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK SLIDING SWITCH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст