Nissan Quest E52. Instruction — part 1263
WT-36
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000009653441
The low tire pressure warning lamp does not illuminate when the ignition switch is turned ON.
NOTE:
The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000009653442
1.
CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Select “ACTIVE TEST” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Touch “WARNING LAMP” to turn ON the low tire pressure warning lamp.
When “ACTIVE TEST” is performed, does the low tire pressure warning lamp in the combination meter turn
ON?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP OPERATION
Check that the low tire pressure warning lamp is turned OFF after turns ON for approximately 1 second, when
the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
BCS-98, "Removal and Installation"
3.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
.
Is the inspection result normal?
YES-1 >> INSPECTION END
NO
>> Repair or replace error-detected parts.
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
WT-37
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000009653443
The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.
Diagnosis Procedure
INFOID:0000000009653444
1.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp display.
Does not low tire pressure warning lamp turn OFF?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
CHECK BCM
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
WT-38
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP BLINKS
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000009653445
The low tire pressure warning lamp blinks when the ignition switch is turned ON.
NOTE:
The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low tire
pressure warning lamp.
Diagnosis Procedure
INFOID:0000000009653446
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> Perform the self-diagnosis for “AIR PRESSURE MONITOR”. Refer to
JPEIC0089GB
EASY FILL TIRE ALERT DOES NOT ACTIVATE
WT-39
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
EASY FILL TIRE ALERT DOES NOT ACTIVATE
Description
INFOID:0000000009653447
The easy fill tire alert does not function while inflating a tire when the select lever position is in P-range with the
ignition switch ON.
NOTE:
• After starting to inflate the tire, it takes a few seconds for the easy fill tire alert to function.
• If there is no response for approximately 15 seconds or more after inflating the tires, cancel the use of the
easy fill tire alert function or move the vehicle approximately 1 m (3.2 ft) backward or forward to try again.
The air filler pressure may be weak or out of service area.
• For easy fill tire alert, Refer to
WT-9, "Easy Fill Tire Alert Function"
Diagnosis Procedure
INFOID:0000000009653448
1.
LOCATION CHANGE
Move the vehicle to other area and repeat the procedure of the easy fill tire alert function. Refer to
Is the function normal?
YES
>> Normal (the easy fill tire alert may not operate, depending on reception condition.)
NO
>> GO TO 2.
2.
PERFORM BCM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK HAZARD WARNING LAMP OPERATION
Check hazard warning lamp operation with hazard switch.
Does the hazard warning lamp blink?
YES
>> GO TO 4.
NO
>> Perform trouble diagnosis for the hazard warning lamp. Refer to
(XENON TYPE),
EXL-196, "Diagnosis Procedure"
(HALOGEN TYPE).
4.
PERFORM TCM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “TRANSMISSION”.
Is any DTC detected?
YES
>> Check malfunctioning circuit. Refer to
NO
>> GO TO 5.
5.
CHECK HORN OPERATION
Check horn operation. Refer to
SEC-120, "Component Function Check"
.
Is the operation normal?
YES
>> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.
PERFORM BCM SELF-DIAGNOSIS
With CONSULT
1.
Drive for 10 minutes at a speed of 40 km/h (25 MPH) or more.
CAUTION:
Total time driving at a speed of 40 km/h (25 MPH) or more must be 10 minutes.
2.
Stop the vehicle.
3.
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is any DTC detected?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст