Nissan Quest E52. Instruction — part 1080
SEC-10
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM
SYSTEM
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION : System Description
INFOID:0000000009650693
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL CHART
Input Signal Item
JMKIA8234GB
SYSTEM
SEC-11
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Output Signal Item
SYSTEM DESCRIPTION
• The engine start function of Intelligent Key system makes it possible to start and stop the engine without
using the key, based on the electronic ID verification. The electronic ID verification is performed between
BCM and Intelligent Key when the push-button ignition switch is pressed while the Intelligent Key is within
the detection area of inside key antenna.
NOTE:
The driver should carry the Intelligent Key at all times.
• Intelligent Key has 2 IDs [Intelligent Key ID and NVIS (NATS) ID]. It can perform the door lock/unlock opera-
tion and the push-button ignition switch operation when the registered Intelligent Key is carried.
• If the ID is successfully verified, when push-button ignition switch is pressed, the engine can be started.
• Up to 4 Intelligent Keys can be registered (Including the standard Intelligent Key) upon request from the cus-
tomer.
NOTE:
Refer to
DLK-36, "INTELLIGENT KEY SYSTEM : System Description"
for any functions other than engine
start function of Intelligent Key system.
PRECAUTIONS FOR INTELLIGENT KEY SYSTEM
The transponder [the chip for NVIS (NATS) ID verification] is integrated into the Intelligent Key. (For the
conventional models, it is integrated into the mechanical key.) Therefore, ID verification cannot be per-
formed by mechanical key only.
In that case, NVIS (NATS) ID verification can be performed when Intelligent Key backside is contacted
to push-button ignition switch while brake pedal is depressed. If verification result is OK, engine can
be started.
OPERATION WHEN INTELLIGENT KEY IS CARRIED
1.
When the push-button ignition switch is pressed, the BCM activates the inside key antenna and transmits
the request signal to the Intelligent Key.
2.
The Intelligent Key receives the request signal and transmits the Intelligent Key ID signal to the BCM.
3.
BCM receives the Intelligent Key ID signal via remote keyless entry receiver and verifies it with the regis-
tered ID.
4.
BCM turns ACC relay ON and transmits the ignition power supply ON signal to IPDM E/R.
Transmit unit
Signal name
ECM
CAN communication
ID verification signal
Engine status signal
IPDM E/R
Push-button ignition switch status signal
Starter relay status signal
Starter control relay signal
Detention switch signal
Interlock/PNP switch signal
Combination meter
Vehicle speed signal (Meter)
ABS actuator and electric unit (control unit)
Vehicle speed signal (ABS)
TCM
Shift position signal
P/N position signal
Remote keyless entry receiver
Key ID signal
Push-button ignition switch
Push-button ignition switch operation signal
Each door switch
Door open/close condition signal
Stop lamp switch
Brake pedal operation signal
CVT shift selector (detention switch)
P position signal
Reception unit
Signal name
Combination meter
CAN communication
Key warning lamp signal
ECM
ID verification signal
Inside key antenna
Key ID request signal
SEC-12
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM
5.
IPDM E/R turns the ignition relay ON and starts the ignition power supply.
6.
IPDM E/R turns the starter control relay ON for engine starting in advance.
7.
BCM detects the selector lever position and brake pedal operation condition.
8.
BCM transmits the starter request signal to IPDM E/R and turns the starter relay in IPDM E/R ON if BCM
judges that the engine start condition* is satisfied.
9.
Power supply is supplied through the starter relay and the starter control relay to operate the starter motor.
CAUTION:
If a malfunction is detected in the Intelligent Key system, the “KEY” warning lamp on the combina-
tion meter illuminates. At that time, the engine cannot be started.
10. When BCM receives feedback signal from ECM indicating that the engine is started, the BCM transmits a
stop signal to IPDM E/R and stops cranking by turning OFF the starter relay. (If engine start is unsuccess-
ful, cranking stops automatically within 5 seconds.)
CAUTION:
When the Intelligent Key is carried outside of the vehicle (inside key antenna detection area) while
the power supply is in the ACC or ON position, even if the engine start condition* is satisfied, the
engine cannot be started.
*: For the engine start condition, refer to “IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUT-
TON IGNITION SWITCH OPERATION”.
OPERATION RANGE
Engine can be started when Intelligent Key is inside the vehicle. However, sometimes engine may not start
when Intelligent Key is on instrument panel or in glove box.
ENGINE START OPERATION WHEN INTELLIGENT KEY IS CONTACTED TO PUSH-BUTTON IG-
NITION SWITCH
When Intelligent Key battery is discharged, NVIS (NATS) ID verification between transponder in Intelligent Key
and BCM is performed when Intelligent Key backside is contacted to push-button ignition switch while brake
pedal is depressed. If the verification result is OK, engine can be started.
IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERA-
TION
The ignition switch position can be changed by the following operations.
NOTE:
• When an Intelligent Key is within the detection area of inside key antenna or when Intelligent Key backside is
contacted to push-button ignition switch, it is equivalent to the operations below.
• When starting the engine, the BCM monitors under the engine start conditions,
CVT models
- Brake pedal operation condition
- Selector lever position
- Vehicle speed
Vehicle speed: less than 4 km/h (2.5 MPH)
Vehicle speed: 4 km/h (2.5 MPH) or more
Power supply position
Condition
Push-button ignition switch operation
frequency
Selector lever
Brake pedal operation
condition
OFF
→
ACC
—
Not depressed
1
OFF
→
ACC
→
ON
—
Not depressed
2
OFF
→
ACC
→
ON
→
OFF
—
Not depressed
3
OFF
→
START
ACC
→
START
ON
→
START
P or N position
Depressed
1
Engine is running
→
OFF
—
—
1
SYSTEM
SEC-13
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Emergency stop operation
• Press and hold the push-button ignition switch for 2 seconds or more.
• Press the push-button ignition switch 3 times or more within 1.5 seconds.
Power supply position
Condition
Push-button ignition switch operation
frequency
Selector lever
Brake pedal operation
condition
Engine is running
→
ACC
—
—
Emergency stop operation
Engine stall return operation
while driving
N position
Not depressed
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст