Nissan Quest E52. Instruction — part 998
PWC-104
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER SIDE WINDOW ANTI-PINCH]
POWER WINDOW MOTOR
PASSENGER SIDE : Component Function Check
INFOID:0000000009653380
1.
CHECK FUNCTION
Check front power window motor (passenger side) operation with power window main switch or front power
window switch (passenger side).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-104, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009653381
1.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (passenger side).
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check continuity between front power window motor (passenger side) harness connector and front power
window switch (passenger side) harness connector.
4.
Check continuity between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-123, "Removal and Installa-
.
NO
>> Repair or replace harness.
SLIDING DOOR LH
(+)
(-)
Condition
Voltage (V)
Front power window motor (passenger side)
Connector
Terminal
D46
1
Ground
Front power window
switch
(passenger side)
NEUTRAL
0 – 1
DOWN
9 – 16
2
NEUTRAL
0 – 1
UP
9 – 16
Front power window motor (passenger side)
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D46
1
D56
6
Existed
2
7
Front power window motor (passenger side)
Ground
Continuity
Connector
Terminal
D46
1
Not existed
2
POWER WINDOW MOTOR
PWC-105
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER SIDE WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
SLIDING DOOR LH : Component Function Check
INFOID:0000000009653382
1.
CHECK FUNCTION
Check sliding door power window motor LH operation with power window main switch or sliding door power
window switch LH.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-105, "SLIDING DOOR LH : Diagnosis Procedure"
SLIDING DOOR LH : Diagnosis Procedure
INFOID:0000000009653383
1.
CHECK SLIDING DOOR POWER WINDOW MOTOR LH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door power window motor LH connector.
3.
Turn ignition switch ON.
4.
Check voltage between sliding door power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door power window motor LH.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR POWER WINDOW MOTOR LH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sliding door power window switch LH connector.
3.
Check continuity between sliding door power window motor LH harness connector and sliding door power
window switch LH harness connector.
4.
Check continuity between sliding door power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door power window switch LH. Refer to
PWC-124, "Removal and Installation"
.
NO
>> Repair or replace harness.
SLIDING DOOR RH
SLIDING DOOR RH : Component Function Check
INFOID:0000000009653384
1.
CHECK FUNCTION
(+)
(-)
Condition
Voltage (V)
Sliding door power window motor LH
Connector
Terminal
D82
1
Ground
Sliding door power
window switch LH
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Sliding door power window motor LH
Sliding door power window switch LH
Continuity
Connector
Terminal
Connector
Terminal
D82
1
D88
5
Existed
3
4
Sliding door power window motor LH
Ground
Continuity
Connector
Terminal
D82
1
Not existed
3
PWC-106
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER SIDE WINDOW ANTI-PINCH]
POWER WINDOW MOTOR
Check sliding door power window motor RH operation with power window main switch or sliding door power
window switch RH.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-106, "SLIDING DOOR RH : Diagnosis Procedure"
SLIDING DOOR RH : Diagnosis Procedure
INFOID:0000000009653385
1.
CHECK SLIDING DOOR POWER WINDOW MOTOR RH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door power window motor RH connector.
3.
Turn ignition switch ON.
4.
Check voltage between sliding door power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door power window motor RH.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR POWER WINDOW MOTOR RH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sliding door power window switch RH connector.
3.
Check continuity between sliding door power window motor RH harness connector and sliding door power
window switch RH harness connector.
4.
Check continuity between sliding door power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door power window switch RH. Refer to
PWC-124, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(-)
Condition
Voltage (V)
Sliding door power window motor RH
Connector
Terminal
D102
1
Ground
Sliding door power
window switch RH
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Sliding door power window motor RH
Sliding door power window switch RH
Continuity
Connector
Terminal
Connector
Terminal
D102
1
D108
5
Existed
3
4
Sliding door power window motor RH
Ground
Continuity
Connector
Terminal
D102
1
Not existed
3
ENCODER CIRCUIT
PWC-107
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER SIDE WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ENCODER CIRCUIT
Component Function Check
INFOID:0000000009653386
1.
CHECK FUNCTION
Check that front driver side door glass perform AUTO UP/DOWN operation normally when power window
main switch is operated.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-107, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009653387
1.
CHECK ENCODER PULSE SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between power window main switch harness connector and ground using an oscilloscope.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-123, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK ENCODER SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and front power window motor (driver side) connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
(+)
(-)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D5
9
Ground
Refer to the following signal
13
JMKIA5210GB
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
9
D7
3
Existed
13
5
Power window main switch
Ground
Continuity
Connector
Terminal
D5
9
Not existed
13
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст