Nissan Quest E52. Instruction — part 403
DLK-326
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR HANDLE SWITCH
SLIDING DOOR HANDLE SWITCH
SLIDING DOOR LH
SLIDING DOOR LH : Component Function Check
INFOID:0000000009649262
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR” using CONSULT.
2.
Select “DOR HAND SW L” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door handle switch is OK.
NO
>> Refer to
DLK-326, "SLIDING DOOR LH : Diagnosis Procedure"
SLIDING DOOR LH : Diagnosis Procedure
INFOID:0000000009649263
1.
CHECK SLIDING DOOR HANDLE SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect remote control assembly LH connector.
3.
Check voltage between remote control assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT
1.
Disconnect sliding door control unit LH connector.
2.
Check continuity between sliding door control unit LH harness connector and remote control assembly LH
harness connector.
3.
Check continuity between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit LH. Refer to
DLK-500, "LH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR HANDLE SWITCH GROUND CIRCUIT
1.
Disconnect sliding door control unit LH connector.
2.
Check continuity between sliding door control unit LH harness connector and remote control assembly LH
harness connector.
Monitor item
Condition
Status
DOR HAND SW L
Sliding door handle LH
Pull
ON
Release
OFF
(+)
(–)
Voltage
Remote control assembly LH
Connector
Terminal
D118
2
Ground
8 – 16 V
Sliding door control unit LH
Remote control assembly LH
Continuity
Connector
Terminal
Connector
Terminal
B45
22
D118
2
Existed
Sliding door control unit LH
Ground
Continuity
Connector
Terminal
B45
22
Not existed
SLIDING DOOR HANDLE SWITCH
DLK-327
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT 2
1.
Connect sliding door control unit LH connector and remote control assembly LH connector.
2.
Check voltage between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door control unit LH. Refer to
DLK-500, "LH : Removal and Installation"
5.
CHECK SLIDING DOOR HANDLE SWITCH
DLK-327, "SLIDING DOOR LH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace remote control assembly LH.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
SLIDING DOOR LH : Component Inspection
INFOID:0000000009649264
1.
CHECK SLIDING DOOR HANDLE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect remote control assembly LH connector.
3.
Check continuity between remote control assembly LH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace remote control assembly LH.
SLIDING DOOR RH
Sliding door control unit LH
Remote control assembly LH
Continuity
Connector
Terminal
Connector
Terminal
B45
23
D118
1
Existed
Sliding door control unit LH
Ground
Continuity
Connector
Terminal
B45
23
Not existed
(+)
(–)
Voltage
Sliding door control unit LH
Connector
Terminal
B45
23
Ground
0 V
Remote control assembly LH
Condition
Continuity
Terminal
2
1
Sliding door handle LH
Pull
Existed
Release
Not existed
DLK-328
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR HANDLE SWITCH
SLIDING DOOR RH : Component Function Check
INFOID:0000000009649265
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR RIGHT” using CONSULT.
2.
Select “DOR HAND SW R” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door handle switch is OK.
NO
>> Refer to
DLK-328, "SLIDING DOOR RH : Diagnosis Procedure"
SLIDING DOOR RH : Diagnosis Procedure
INFOID:0000000009649266
1.
CHECK SLIDING DOOR HANDLE SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect remote control assembly RH connector.
3.
Check voltage between remote control assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and remote control assembly
RH harness connector.
3.
Check continuity between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit RH. Refer to
DLK-500, "RH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR HANDLE SWITCH GROUND CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and remote control assembly
RH harness connector.
Monitor item
Condition
Status
DOR HAND SW R
Sliding door handle RH
Pull
ON
Release
OFF
(+)
(–)
Voltage
Remote control assembly RH
Connector
Terminal
D127
2
Ground
8 – 16 V
Sliding door control unit RH
Remote control assembly RH
Continuity
Connector
Terminal
Connector
Terminal
B247
22
D127
2
Existed
Sliding door control unit RH
Ground
Continuity
Connector
Terminal
B247
22
Not existed
SLIDING DOOR HANDLE SWITCH
DLK-329
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT 2
1.
Connect sliding door control unit RH connector and remote control assembly RH connector.
2.
Check voltage between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door control unit RH. Refer to
DLK-500, "RH : Removal and Installation"
5.
CHECK SLIDING DOOR HANDLE SWITCH
DLK-329, "SLIDING DOOR RH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace remote control assembly RH.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
SLIDING DOOR RH : Component Inspection
INFOID:0000000009649267
1.
CHECK SLIDING DOOR HANDLE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect remote control assembly RH connector.
3.
Check continuity between remote control assembly RH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace remote control assembly RH.
Sliding door control unit RH
Remote control assembly RH
Continuity
Connector
Terminal
Connector
Terminal
B247
23
D127
1
Existed
Sliding door control unit RH
Ground
Continuity
Connector
Terminal
B247
23
Not existed
(+)
(–)
Voltage
Sliding door control unit RH
Connector
Terminal
B247
23
Ground
0 V
Remote control assembly RH
Condition
Continuity
Terminal
2
1
Sliding door handle RH
Pull
Existed
Release
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст