Nissan Quest E52. Instruction — part 659
SQUEAK AND RATTLE TROUBLE DIAGNOSES
EXT-11
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
PIIB8742E
EXT-12
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000009650486
Removal and Installation
INFOID:0000000009650487
CAUTION:
1.
Bumper side bracket RH
2.
Screw grommet
3.
Bumper stay RH
4.
Bumper reinforcement
5.
Bumper energy absorber
6.
Bumper fascia
7.
Front fog lamp RH
8.
Bumper finisher RH
9.
Bumper bracket cover
10.
License plate bracket
11.
Bumper finisher LH
12.
Front fog lamp LH
13.
Bumper stay LH
14.
Bumper side bracket LH
: Pawl
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA8213ZZ
FRONT BUMPER
EXT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1.
Fully open hood assembly.
2.
Remove front grille. Refer to
EXT-18, "Removal and Installation"
3.
Remove fender protector (front) fixing clips and screws to access bumper fascia assembly fixing screw.
Refer to
EXT-23, "Removal and Installation"
.
4.
Remove bumper fascia both ends fixing screws (A).
5.
Remove bumper fascia assembly upper side fixing clips (A).
CAUTION:
Apply protective tape (B) around bumper fascia.
6.
Remove bumper fascia assembly lower side fixing clips.
7.
Pull bumper fascia assembly toward the vehicle out side as
shown by the arrows in the figure, and then disengage bumper
fascia assembly from bumper side brackets (LH and RH).
CAUTION:
When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.
8.
Disconnect front fog lamp harness connectors (LH and RH).
9.
Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
10. Remove the following parts after removing bumper fascia.
• Front fog lamp assembly (LH and RH). (with fog lamp)
• Front fog lamp finishers (LH and RH). (without fog lamp)
• Bumper bracket cover
• Front spoiler
• License plate bracket
11. Remove bumper energy absorber.
12. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
13. Remove bumper side bracket mounting screws, and then remove bumper side bracket.
JMKIA8182ZZ
JMKIA8181ZZ
: Pawl
JMKIA8183ZZ
EXT-14
< REMOVAL AND INSTALLATION >
FRONT BUMPER
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal
installation status.
• Fitting adjustment cannot be performed.
JMKIA8184ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Front grille
A – A
0.0 – 3.0 mm
(0.000 – 0.118 in)
—
Bumper fascia assembly –
Front combination lamp
B – B
0.1 – 2.9 mm
(0.004 – 0.114 in)
—
Bumper fascia assembly –
Front fender
C – C
0.0 – 0.8 mm
(0.000 – 0.031 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст