Nissan Quest E52. Instruction — part 1229
TM-146
< SYMPTOM DIAGNOSIS >
[CVT: RE0F09B]
SYSTEM SYMPTOM
21
Others
Maximum speed low.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Accelerator pedal position sensor
4. CAN communication line
5. Stall test
6. Step motor
7. Primary speed sensor
8. Secondary speed sensor
9. Primary pressure sensor
10. Secondary pressure sensor
11. CVT fluid temperature sensor
OFF vehicle
12. Torque converter
13. Oil pump assembly
14. Gear system
15. Forward clutch
16. Control valve
22
With selector lever in
“P” position, vehicle
does not enter parking
condition or, with se-
lector lever in another
position, parking con-
dition is not cancelled.
ON vehicle
1. Transmission range switch
2. CVT position
OFF vehicle
3. Parking components
23
Vehicle drives with
CVT in “P” position.
ON vehicle
1. Transmission range switch
2. CVT fluid level and state
3. CVT position
OFF vehicle
4. Parking components
5. Gear system
6. Control valve
24
Vehicle drives with
CVT in “N” position.
ON vehicle
1. Transmission range switch
2. CVT fluid level and state
3. CVT position
OFF vehicle
4. Gear system
5. Forward clutch
6. Reverse brake
7. Control valve
No.
Item
Symptom
Condition
Diagnostic item
Reference
SYSTEM SYMPTOM
TM-147
< SYMPTOM DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
25
Others
Engine stall.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. Primary speed sensor
4. Torque converter clutch solenoid valve
5. CAN communication line
6. Stall test
7. Secondary pressure sensor
OFF vehicle
8. Torque converter
9. Control valve
26
Engine stalls when
selector lever is shift-
ed “N”
→
“D” or “R”.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. Primary speed sensor
4. Torque converter clutch solenoid valve
5. CAN communication line
6. Stall test
OFF vehicle
7. Torque converter
8. Control valve
27
Engine speed does
not return to idle.
ON vehicle
1. CVT fluid level and state
2. Accelerator pedal position sensor
3. Secondary speed sensor
4. CAN communication line
OFF vehicle
5. Control valve
28
CVT does not shift
ON vehicle
1. CVT fluid level and state
2. CVT position
3. Line pressure test
4. Engine speed signal
5. Accelerator pedal position sensor
6. CAN communication line
7. Primary speed sensor
8. Secondary speed sensor
9. Step motor
OFF vehicle
10. Control valve
11. Oil pump assembly
29
Engine does not start
in “N” or “P” position.
ON vehicle
1. Ignition switch and starter
2. CVT position
3. Transmission range switch
No.
Item
Symptom
Condition
Diagnostic item
Reference
TM-148
< SYMPTOM DIAGNOSIS >
[CVT: RE0F09B]
SYSTEM SYMPTOM
30
Others
Engine starts in posi-
tions other than “N” or
“P”.
ON vehicle
1. Ignition switch and starter
2. CVT position
3. Transmission range switch
31
When brake pedal is
depressed with igni-
tion switch ON, selec-
tor lever cannot be
shifted from “P” posi-
tion to other position.
ON vehicle
1. Stop lamp switch
2. Shift lock solenoid
3. CVT shift selector
32
When brake pedal is
not depressed with ig-
nition switch ON, se-
lector lever can be
shifted from “P” posi-
tion to other position.
ON vehicle
1. Stop lamp switch
2. Shift lock solenoid
3. CVT shift selector
33
Cannot be changed to
overdrive OFF condi-
tion.
ON vehicle
1. Overdrive control switch
2. CAN communication line
3. Combination meter
34
OD OFF indicator
lamp is not turned ON.
ON vehicle
1. CAN communication line
2. Combination meter
3. TCM power supply and ground
No.
Item
Symptom
Condition
Diagnostic item
Reference
CVT FLUID
TM-149
< PERIODIC MAINTENANCE >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PERIODIC MAINTENANCE
CVT FLUID
Inspection
INFOID:0000000009650219
CHECKING CVT FLUID
The fluid level should be checked with the fluid warmed up to 50 to 80
°
C (122 to 176
°
F). The fluid level check
procedure is as follows:
1.
Check for fluid leakage.
2.
With the engine warmed up, drive the vehicle in an urban area.
When ambient temperature is 20
°
C (68
°
F), it takes about 10
minutes for the CVT fluid to warm up to 50 to 80
°
C (122 to
176
°
F).
3.
Park the vehicle on a level surface.
4.
Apply parking brake firmly.
5.
With engine at idle, while depressing brake pedal, move shift
selector throughout the entire shift range.
6.
Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.
7.
Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180
°
from the originally installed position,
then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.
CAUTION:
When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.
8.
Place the selector lever in “P” or “N” and check that the fluid
level is within the specified range.
CAUTION:
When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until securely locked.
CVT FLUID CONDITION
SMA146B
SCIA1933E
SCIA1931E
SCIA1932E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст