Nissan Quest E52. Instruction — part 1225
TM-130
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
Component Function Check
INFOID:0000000009650207
1.
CHECK SHIFT POSITION INDICATOR
1.
Start the engine.
2.
Check that correct selector lever position (“P”, “R”, “N”, “D”, “L”) is displayed as selector lever is moved
into each position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009650208
1.
CHECK INPUT SIGNALS
With CONSULT
1.
Start the engine.
2.
Select “Data Monitor” in “TRANSMISSION”.
3.
Select “RANGE”.
4.
Check that correct selector lever position (“P”, “R”, “N”, “D”, “L”) is displayed as selector lever is moved
into each position.
Is the inspection result normal?
YES
>> INSPECTION END
NO-1 (The actual gear position changes, but the shift position indicator is not indicated.)>>Perform
“Self
Diagnostic Results” in “TRANSMISSION”.
NO-2 (The actual gear position and the indication on the shift position indicator do not coincide.)>>Perform
“Self Diagnostic Results” in “TRANSMISSION”.
NO-3 (Only a specific position or positions is/are not indicated on the shift position indicator.)>>Check
the
combination meter. Refer to
OVERDRIVE CONTROL SWITCH
TM-131
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OVERDRIVE CONTROL SWITCH
Component Function Check
INFOID:0000000009650209
1.
CHECK O/D OFF INDICATOR LAMP
When ignition switch is turned ON, check that O/D OFF indicator lamp in combination meter illuminates during
2 seconds approximately.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Go to
2.
CHECK OVERDRIVE CONTROL SWITCH
1.
Shift the selector lever to “D” position.
2.
When overdrive control switch is operated, check that O/D OFF indicator lamp in combination meter illu-
minates/extinguishes.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009650210
1.
CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the CVT shift selector connector.
3.
Turn ignition switch ON.
4.
Check the voltage between CVT shift selector harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OVERDRIVE CONTROL SWITCH
Check the overdrive control switch. Refer to
TM-132, "Component Inspection (Overdrive Control Switch)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK CVT SHIFT SELECTOR HARNESS
Check the continuity between harness plate (A) and CVT shift selec-
tor (B).
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
NO
>> Replace the CVT shift selector assembly. Refer to
.
CVT shift selector
Voltage (Approx.)
Connector
+
−
Terminal
M57
1
4
12 V
Harness plate
CVT shift selector
Continuity
Terminal
C
1
Existed
D
4
JSDIA2669GB
TM-132
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
OVERDRIVE CONTROL SWITCH
4.
CHECK GROUND CIRCUIT
Check the continuity between CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK HARNESS BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER
1.
Turn ignition switch OFF.
2.
Disconnect the combination meter connector.
3.
Check the continuity between CVT shift selector harness connector terminal and combination meter har-
ness connector terminal.
4.
Check continuity between CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK COMBINATION METER INPUT SIGNAL
1.
Connect all of the disconnected connectors.
2.
Turn ignition switch ON.
3.
Select “Data Monitor” in “METER/M&A”.
4.
Select “O/D OFF SW”.
5.
Check that “O/D OFF SW” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Replace the combination meter. Refer to
.
Component Inspection (Overdrive Control Switch)
INFOID:0000000009650211
1.
CHECK OVERDRIVE CONTROL SWITCH
Check the continuity between wires of select lever knob (1).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the selector lever knob. Refer to
.
CVT shift selector
—
Continuity
Connector
Terminal
M57
4
Ground
Existed
CVT shift selector
Combination meter
Continuity
Connector
Terminal
Connector
Terminal
M57
1
M34
32
Existed
CVT shift selector
—
Continuity
Connector
Terminal
M57
1
Ground
Not existed
Condition
Continuity
Overdrive control switch is depressed
Existed
Overdrive control switch is released
Not existed
JSDIA2668ZZ
OD OFF INDICATOR LAMP
TM-133
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OD OFF INDICATOR LAMP
Component Function Check
INFOID:0000000009650212
1.
CHECK O/D OF INDICATOR LAMP
When ignition switch is turned ON, check that O/D OFF indicator lamp in combination meter illuminates during
2 seconds approximately.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009650213
1.
CHECK DTC (TCM)
With CONSULT
1.
Turn ignition switch ON.
2.
Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
.
NO
>> GO TO 2.
2.
CHECK DTC (COMBINATION METER)
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
With CONSULT
1.
Shift the selector lever to “D” position.
2.
Select “Data Monitor” in “METER/M&A”.
3.
Select “O/D OFF IND”.
4.
Check that “O/D OFF IND” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
.
NO
>> GO TO 4.
4.
CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1.
Select “Data Monitor” in “TRANSMISSION”.
2.
Select “SPORT MODE SW”.
3.
Check that “SPORT MODE SW” turns ON/OFF when overdrive control switch is operated. Refer to
.
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
.
NO
>> Check the overdrive control switch. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст