Nissan Quest E52. Instruction — part 1133
B1036 CRASH ZONE SENSOR
SRC-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1036 CRASH ZONE SENSOR
DTC Logic
INFOID:0000000009649877
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009649878
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE CRASH ZONE SENSOR
1.
Replace crash zone sensor. Refer to
SR-23, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1036
CRASH ZONE SEN
[UNMATCH]
Crash zone sensor is out of the specified speci-
fication
Diagnosis sensor unit or crash zone sensor is
different from the part specified
SRC-62
< DTC/CIRCUIT DIAGNOSIS >
B1037, B1039, B1041 CRASH ZONE SENSOR
B1037, B1039, B1041 CRASH ZONE SENSOR
DTC Logic
INFOID:0000000009649879
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009649880
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE CRASH ZONE SENSOR
1.
Replace crash zone sensor. Refer to
SR-23, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1037
B1039
B1041
CRASH ZONE SENS1
Crash zone sensor is malfunctioning
• Disconnection of wiring harness
• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sensor unit
B1037, B1039, B1041 CRASH ZONE SENSOR
SRC-63
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> INSPECTION END
SRC-64
< DTC/CIRCUIT DIAGNOSIS >
B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT
B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009649881
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009649882
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1042
B1043
B1044
B1045
B1046
B1047
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст