Nissan Quest E52. Instruction — part 148
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-471
< SYSTEM DESCRIPTION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
Error item
Description
Possible malfunction factor/Action to take
CAN COMM CIRCUIT
CAN communication malfunction is detect-
ed.
Perform diagnosis with CONSULT, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
Refer to
CONTROL UNIT (CAN)
CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit if the malfunc-
tion occurs constantly.
Refer to
AV-610, "Removal and Installa-
.
CONTROL UNIT (AV)
AV communication circuit initial diagnosis
malfunction is detected.
FLASH-ROM Error Of Control Unit
AV control unit malfunction is detected.
Connection Of Gyro
Connection of G Sensor
CAN Controller Memory Error
Bluetooth Module Connection Error
Sub CPU Connection Error
iPod authentification chip error
Audio connection error
DSP Connection Error
AV control unit malfunction is detected.
• If a disc can be played, then there is a
possibility of the detection of a temporary
malfunction.
• Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV-610, "Removal and Installa-
DSP Communication Error
HDD Connection Error
AV control unit malfunction is detected.
Replace the AV control unit if the malfunc-
tion occurs constantly.
Refer to
AV-610, "Removal and Installa-
.
HDD Read Error
HDD Write Error
HDD Communication Error
HDD Access Error
GPS Communication Error
GPS malfunction is detected.
• An intermittent error caused by strong ra-
dio interference may be detected unless
any symptom (GPS reception error, etc.)
occurs.
• Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV-610, "Removal and Installa-
GPS ROM Error
GPS RAM Error
GPS RTC Error
Unfinished configuration
The writing of configuration data is incom-
plete.
Write configuration data with CONSULT.
USB Controller Communication Error
USB connection malfunction is detected.
Check that the connection to the USB con-
nector is normal.
DVD Mechanism Communication Error
AV control unit malfunction is detected.
• If DVD can be played, then there is a
possibility of the detection of a temporary
malfunction.
• Replace the AV control unit if the mal-
function occurs constantly.
Refer to
AV-610, "Removal and Installa-
Steer. Angle Sensor Calibration
Neutral position adjustment of the steering
angle sensor is incomplete.
Adjust the neutral position of the steering
angle sensor.
Refer to
AV-472
< SYSTEM DESCRIPTION >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Vehicle CAN Diagnosis
• CAN communication status and error counter is displayed.
• The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
• The error counter is erased if “Reset” is pressed.
NOTE:
“???” indicates UNKWN.
AV COMM Diagnosis
Front Display Connection Error
When either one of the following items are
detected:
• front display unit power supply and
ground circuits are malfunctioning.
• serial communication circuits between
AV control unit and front display unit are
malfunctioning.
• Front display unit power supply and
ground circuits.
Refer to
• Serial communication circuits between
AV control unit and front display unit.
AM/FM antenna amplifier short to ground
Radio antenna amp. ON signal circuit mal-
function is detected.
Radio antenna amp. ON signal circuit be-
tween AV control unit and antenna amp.
AM/FM antenna amplifier open
Ext_Amp_ON output terminal short to
ground
BOSE amp. ON signal circuit malfunction is
detected.
BOSE amp. ON signal circuit between AV
control unit and BOSE amp.
Ext_Amp_ON output terminal :open
GPS Antenna Error
GPS antenna connection malfunction is de-
tected.
Check the connection of the GPS antenna
connector.
USB electric current Error
Detection of overcurrent in USB connector.
Check USB harness between the AV con-
trol unit and USB connector.
XM Antenna Connection Error
Satellite radio antenna connection malfunc-
tion is detected.
Satellite radio antenna disconnection.
• AV COMM CIRCUIT
• Switches Connection Error
When either one of the following items are
detected:
• multifunction switch power supply and
ground circuits are malfunctioning.
• AV communication circuits between AV
control unit and multifunction switch were
malfunctioning.
• Multifunction switch power supply and
ground circuits.
• AV communication circuits between AV
control unit and multifunction switch.
• AV COMM CIRCUIT
• 2nd Display Connection Error
When either one of the following items are
detected:
• Rear display unit power supply and
ground circuits are malfunctioning.
• AV communication circuits between AV
control unit and rear display unit are mal-
functioning.
• Rear display unit power supply and
ground circuits.
Refer to
.
• AV communication circuits between AV
control unit and rear display unit.
• AV COMM CIRCUIT
• Switches Connection Error
• 2nd Display Connection Error
AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.
AV communication circuits between AV
control unit and multifunction switch.
Error item
Description
Possible malfunction factor/Action to take
Items
Display (Current)
Malfunction counter
(Past)
Tx(HVAC)
OK / ???
OK / 0 – 39
Rx(ECM)
OK / ???
OK / 0 – 39
Rx(Cluster)
OK / ???
OK / 0 – 39
Rx(HVAC)
OK / ???
OK / 0 – 39
Rx(USM)
OK / ???
OK / 0 – 39
Rx(STRG)
OK / ???
OK / 0 – 39
JSNIA2181ZZ
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-473
< SYSTEM DESCRIPTION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• Displays the communication status between AV control unit (mas-
ter unit) and each unit.
• The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
• The error counter is erased if “Reset” is pressed.
NOTE:
“???” indicates UNKWN
Hands-Free Phone
The hands-free phone reception volume adjustment and microphone
and speaker test functions are also available.
Delete Unit Connection Log
Deletes any unit connection records and error records from the AV
control unit memory. (Clear the records of the unit that has been
removed.)
Initialize Settings
Items
Status
(Current)
Counter
(Past)
C Tx(ITM–PrimarySW)
OK / ???
OK / 0 – 39
C Rx(PrimarySW–ITM)
OK / ???
OK / 0 – 39
C Rx(Video Dist–ITM)
OK / ???
OK / 0 – 39
C Rx(Remote Cont–ITM)
OK / ???
OK / 0 – 39
JSNIA3216ZZ
JSNIA2183ZZ
JSNIA2189ZZ
AV-474
< SYSTEM DESCRIPTION >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
“User Data Initialization” and “Accessory Number Initialization” are
possible.
CAUTION:
• Never perform Accessory Number Initialization except when
configuration is unsuccessful.
• Accessory Number Initialization requires configuration. For
details, refer to
AV-526, "CONFIGURATION (AV CONTROL
Version Information
Version information of the AV control unit is displayed.
CONSULT Function
INFOID:0000000009652277
CONSULT FUNCTIONS
CONSULT performs the following functions via the communication with the AV control unit.
AV Communication
When “AV communication” of “CAN Diag Support Monitor” is selected, the following function will be performed.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSIS RESULT
• In CONSULT self-diagnosis, self-diagnosis results and error history are displayed collectively.
• The current malfunction indicates “CRNT”. The past malfunction indicates “PAST”.
• The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis Results Display Item
JSNIA2190ZZ
JSNIA2191ZZ
Diagnosis mode
Description
Ecu Identification
The part number of AV control unit can be checked.
Self Diagnostic Result
Performs a diagnosis on the AV control unit and a connection diagnosis for the communication
circuit of the Multi AV system, and displays the current and past malfunctions collectively.
Data Monitor
The diagnosis of vehicle signal that is input to the AV control unit can be performed.
Work Support
Steering angle sensor can be adjusted.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing AV control unit.
AV communication
AV&NAVI C/U
Displays the communication status from AV control unit to each unit as well as the error
counter.
AUDIO
Displays the AV control unit communication status and the error counter.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст