Nissan Quest E52. Instruction — part 195
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: For models without auto light system, this item is not displayed.
*
2
: For models without front fog lamp, this item is displayed but is not monitored.
ACTIVE TEST
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter via CAN communi-
cation
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from sliding door switch RH
DOOR SW- RL
[On/Off]
The switch status input from sliding door switch LH
DOOR SW-BK
[On/Off]
The switch status input from back door switch
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item is indicated, but can not monitored
OPTI SEN (DTCT)*
1
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)*
1
[V]
The value of outside brightness voltage filtered by BCM
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
BCS-24
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without front fog lamp, this item is displayed but is not tested.
*
2
: For models without daytime running light system, this item is not displayed.
*
3
: Except for CANADA
HEADLAMP : CONSULT Function (BCM - HEADLAMP) (Halogen Type Headlamp)
INFOID:0000000009978876
WORK SUPPORT
*
1
: For models without auto light system, this item is displayed but is not operated.
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
FR FOG LAMP*
1
On
Transmits the front fog light request signal to IPDM E/R via CAN commu-
nication to turn the front fog lamp ON
Off
Stops the front light request signal transmission
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R
Off
Stop the daytime running light request signal transmission
ILL DIM SIGNAL
On
• Transmits the dimmer signal to combination meter via CAN communi-
cation and dims combination meter*
3
• Transmits the dimmer signal to AV control unit and dims display
Off
Stops the dimmer signal transmission
Test item
Operation
Description
Service item
Setting item
Setting
CUSTOM A/LIGHT SET-
TING*
1
MODE 1*
3
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
BATTERY SAVER SET
On*
3
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET*
1
MODE 1*
3
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE 2
Without the
function
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
AUTO LIGHT LOGIC SET*
2
MODE 1*
3
With twilight ON custom & with wiper INT, LO and HI
MODE 2
With twilight ON custom & with wiper LO and HI
MODE 3
With twilight ON custom & without
MODE 4
Without twilight ON custom & with wiper INT, LO and HI
MODE 5
Without twilight ON custom & with wiper LO and HI
MODE 6
Without twilight ON custom & without
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
2
: For models without auto light system and all models for Canada, this item is displayed but is not operated.
*
3
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
*
1
: For models without auto light system, this item is not displayed.
*
2
: For models without front fog lamp, this item is displayed but is not monitored.
ACTIVE TEST
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter via CAN communi-
cation
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from sliding door switch RH
DOOR SW- RL
[On/Off]
The switch status input from sliding door switch LH
DOOR SW-BK
[On/Off]
The switch status input from back door switch
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item is indicated, but can not monitored
OPTI SEN (DTCT)*
1
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)*
1
[V]
The value of outside brightness voltage filtered by BCM
BCS-26
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without front fog lamp, this item is displayed but is not tested.
*
2
: For models without daytime running light system, this item is not displayed.
*
3
: Except for CANADA
WIPER
WIPER : CONSULT Function (BCM - WIPER)
INFOID:0000000009978881
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
FR FOG LAMP*
1
On
Transmits the front fog light request signal to IPDM E/R via CAN commu-
nication to turn the front fog lamp ON
Off
Stops the front light request signal transmission
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R
Off
Stop the daytime running light request signal transmission
ILL DIM SIGNAL
On
• Transmits the dimmer signal to combination meter via CAN communi-
cation and dims combination meter*
3
• Transmits the dimmer signal to AV control unit and dims display
Off
Stops the dimmer signal transmission
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wip-
er intermittent dial position)
The setting of front wip-
er INT operation can be
changed
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial
position)
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch.
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст