Nissan Quest E52. Instruction — part 19
SEAT MEMORY SWITCH
ADP-69
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-111, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK SEAT MEMORY SWITCH GROUND CIRCUIT
Check continuity between seat memory switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK SEAT MEMORY SWITCH
ADP-69, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Replace seat memory switch. Refer to
ADP-113, "Removal and Installation"
Component Inspection
INFOID:0000000009649658
1.
CHECK SEAT MEMORY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect seat memory switch connector.
3.
Check continuity between seat memory switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace seat memory switch. Refer to
ADP-113, "Removal and Installation"
Driver seat control unit
Ground
Continuity
Connector
Terminal
B552
6
Not existed
22
28
Seat memory switch
Ground
Continuity
Connector
Terminal
D13
4
Existed
Seat memory switch
Condition
Continuity
Terminal
1
4
Memory switch 1
Push
Existed
Release
Not existed
2
Memory switch 2
Push
Existed
Release
Not existed
3
Set switch
Push
Existed
Release
Not existed
ADP-70
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
DOOR MIRROR REMOTE CONTROL SWITCH
MIRROR SWITCH
MIRROR SWITCH : Component Function Check
INFOID:0000000009649659
1.
CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
ADP-70, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000009649660
1.
CHECK MIRROR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK MIRROR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
MIR CON SW-UP/DN
When operating the mirror switch toward the up or down side.
: ON
Other than the above.
: OFF
MIR CON SW-RH/LH
When operating the mirror switch toward the right or left side.
: ON
Other than the above.
: OFF
(+)
(-)
Voltage (V)
Door mirror remote control switch
Connector
Terminal
D14
4
Ground
4 – 6
12
13
15
Automatic drive positioner control unit Door
mirror
remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
3
D14
15
Existed
4
13
15
12
16
4
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-71
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-112, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK MIRROR SWITCH
Check door mirror remote control switch.
Refer to
ADP-71, "MIRROR SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch.
MIRROR SWITCH : Component Inspection
INFOID:0000000009649661
1.
CHECK MIRROR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch.
CHANGEOVER SWITCH
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
3
Not existed
4
15
16
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
Door mirror remote control switch
Condition
Continuity
Terminal
4
7
Mirror switch
RIGHT
Existed
Other than the above
Not existed
12
DOWN
Existed
Other than the above
Not existed
13
LEFT
Existed
Other than the above
Not existed
15
UP
Existed
Other than the above
Not existed
ADP-72
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000009649662
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
ADP-72, "CHANGEOVER SWITCH : Diagnosis Procedure"
.
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000009649663
1.
CHECK CHANGEOVER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK CHANGEOVER SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-112, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Monitor item
Condition
MIR CHNG SW-R/L
When operating the changeover toward the right or left side.
: ON
Other than the above.
: OFF
(+)
(-)
Voltage (V)
Door mirror remote control switch
Connector
Terminal
D14
10
Ground
4 – 6
11
Automatic drive positioner control unit Door
mirror
remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
2
D14
11
Existed
14
10
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
2
Not existed
14
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст