Nissan Quest E52. Instruction — part 1086
SEC-34
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT)
INFOID:0000000009650701
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
P RANGE
This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-button ignition switch illumination operation
• On: Operate
• Off: Non-operation
LOCK INDICATOR
This test is able to check LOCK indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
ACC INDICATOR
This test is able to check ACC indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
IGNITION ON IND
This test is able to check ON indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
HORN
This test is able to check horn operation
• On: Operate
• Off: Non-operation
TRUNK/BACK DOOR
NOTE:
This item is displayed, but cannot be used
POWER SLIDE DOOR
This test is able to check automatic siding door operation
• RR PSD ON: Auto open/close operate
• RL PSD ON: Auto open/close operate
Test item
Description
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -RR
NOTE:
This is displayed even when it is not equipped.
REQ SW -RL
NOTE:
This is displayed even when it is not equipped.
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DIAGNOSIS SYSTEM (BCM)
SEC-35
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ACTIVE TEST
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000009650702
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from door key cylinder.
TR/BD OPEN SW
Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR
NOTE:
This is displayed even when it is not equipped.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This is displayed even when it is not equipped.
Monitored Item
Description
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horns operation.
Horns are activated for 0.5 seconds after “ON” on CONSULT screen is touched.
HEADLAMP(HI)
This test is able to check headlamp operation.
Headlamps are activated for 0.5 seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation.
Hazard warning lamps are activated after “ON” on CONSULT screen is touched.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.
SEC-36
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Monitor item
Content
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.
DIAGNOSIS SYSTEM (IPDM E/R)
SEC-37
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT Function (IPDM E/R)
INFOID:0000000009982301
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
MOTOR FAN REQ
[1/2/3/4]
×
Displays the value of the cooling fan speed signal received from ECM via CAN com-
munication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN com-
munication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via CAN
communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper stop position signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN com-
munication.
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the shift position judged by IPDM E/R.
ST RLY CONT
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN
communication.
IHBT RLY -REQ
[Off/On]
Displays the status of the starter control relay signal received from BCM via CAN
communication.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст