Nissan Quest E52. Instruction — part 738
HAC-82
< BASIC INSPECTION >
[AUTOMATIC AIR CONDITIONING]
SYSTEM SETTING
SYSTEM SETTING
Temperature Setting Trimmer (Front)
INFOID:0000000009652540
DESCRIPTION
If the temperature felt by the customer is different from the front air flow temperature controlled by the temper-
ature setting, the A/C auto amp. control temperature can be adjusted to compensate for the temperature set-
ting.
HOW TO SET
1.
Starts on board self-diagnosis STEP 5 mode (Each sensor recognition temperature check; “51” or “52” is
indicated on front A/C control display).
2.
Press fan switch (up: +) and check that “61” is indicated on front A/C control display.
3.
After approximately 3 seconds, the temperature setting trimmer (front) can be available.
4.
The indication will be changed by “5” (“1”) in range of
−
3.0
°
C (
−
6
°
F) to +3.0
°
C (6
°
F) by pressing the tem-
perature control switch (driver side) each time. Press temperature control switch (driver side) ( ) to
increase the set temperature, and press temperature control switch (driver side) ( ) to decrease the set
temperature. When balance setting is minus, A/C switch indicator is turned ON.
Models for Canada
Models for USA
Display
Correction (
°
C)
30
+3.0
25
+2.5
20
+2.0
15
+1.5
10
+1.0
5
+0.5
0
0 (Initial setting)
5
−
0.5
10
−
1.0
15
−
1.5
20
−
2.0
25
−
2.5
30
−
3.0
Display
Correction (
°
F)
6
+6
5
+5
4
+4
3
+3
2
+2
1
+1
0
0 (Initial setting)
1
−
1
2
−
2
3
−
3
4
−
4
SYSTEM SETTING
HAC-83
< BASIC INSPECTION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
: A/C switch indicator
NOTE:
• When
−
3
°
C (
−
6
°
F) is selected on the temperature setting set as 25
°
C (75
°
F), the temperature controlled by
A/C auto amp. is 25
°
C (75
°
F)
−
3
°
C (6
°
F) = 22.0
°
C (69
°
F), and then the temperature becomes lower than
the temperature setting.
• When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10
V or less, the setting of the difference between the set temperature and control temperature may be can-
celled.
Temperature Setting Trimmer (Rear)
INFOID:0000000009652541
DESCRIPTION
If the temperature felt by the customer is different from the rear air flow temperature controlled by the temper-
ature setting, the A/C auto amp. control temperature can be adjusted to compensate for the temperature set-
ting.
HOW TO SET
1.
Starts on board self-diagnosis STEP 5 mode (Each sensor recognition temperature check; “51” or “52” is
indicated on front A/C control display).
2.
Press fan switch (up: +) and check that “61” is indicated on front A/C control display.
3.
After approximately 3 seconds, the temperature setting trimmer (rear) can be available.
4.
The indication will be changed by “5” (“1”) in range of
−
3.0
°
C (
−
6
°
F) to +3.0
°
C (6
°
F) by pressing the tem-
perature control switch (passenger side) each time. Press temperature control switch (passenger side)
( ) to increase the set temperature, and press temperature control switch (passenger side) ( ) to
decrease the set temperature. When balance setting is minus, REAR switch indicator is turned ON.
Models for Canada
Models for USA
5
−
5
6
−
6
Display
Correction (
°
F)
Display
Correction (
°
C)
30
+3.0
25
+2.5
20
+2.0
15
+1.5
10
+1.0
5
+0.5
0
0 (Initial setting)
5
−
0.5
10
−
1.0
15
−
1.5
20
−
2.0
25
−
2.5
30
−
3.0
Display
Correction (
°
F)
6
+6
5
+5
4
+4
3
+3
2
+2
HAC-84
< BASIC INSPECTION >
[AUTOMATIC AIR CONDITIONING]
SYSTEM SETTING
: REAR switch indicator
NOTE:
• When
−
3
°
C (
−
6
°
F) is selected on the temperature setting set as 25
°
C (75
°
F), the temperature controlled by
A/C auto amp. is 25
°
C (75
°
F)
−
3
°
C (6
°
F) = 22.0
°
C (69
°
F), and then the temperature becomes lower than
the temperature setting.
• When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10
V or less, the setting of the difference between the set temperature and control temperature may be can-
celled.
Foot Position Setting Trimmer
INFOID:0000000009652542
DESCRIPTION
In FOOT mode, the air blowing to DEF can be turned ON/OFF.
HOW TO SET
1.
Starts on board self-diagnosis STEP 5 mode (Each sensor recognition temperature check; “51” or “52” is
indicated on front A/C control display).
2.
Press fan switch (up: +) and check that “61” is indicated on front A/C control display.
3.
After approximately 3 seconds, the foot position setting trimmer can be available.
4.
Press MODE switch to select FOOT mode type as shown below.
NOTE:
When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V
or less, the setting of the foot position setting trimmer may be cancelled.
Inlet Port Memory Function
INFOID:0000000009652543
DESCRIPTION
• Air inlet is memorized when ignition switch is turned OFF, and the air inlet can be set either REC (recircula-
tion), FRE (fresh air intake), or “Do not perform the memory” when ignition switch is turned ON again.
• When “Do not perform the memory” is set, the air inlet is controlled automatically when ignition switch is
turned ON again.
HOW TO SET
1.
Starts on board self-diagnosis STEP 5 mode (Each sensor recognition temperature check; “51” or “52” is
indicated on front A/C control display).
2.
Press fan switch (up: +) and check that “61” is indicated on front A/C control display.
1
+1
0
0 (Initial setting)
1
−
1
2
−
2
3
−
3
4
−
4
5
−
5
6
−
6
Display
Correction (
°
F)
Type
Display
Defroster door position
Auto control
Instruction control
Type-A
OPEN
CLOSE
Type-B (Initial setting)
OPEN
OPEN
Type-C
CLOSE
OPEN
Type-D
CLOSE
CLOSE
SYSTEM SETTING
HAC-85
< BASIC INSPECTION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
3.
After approximately 3 seconds, the inlet port memory function can be available.
4.
Press AUTO intake switch or intake switch to set the inlet port memory function as per the following. [with
ACCS (Advanced Climate Control System)]
Press FRE switch or REC switch to set the inlet port memory function as per the following. [without ACCS
(Advanced Climate Control System)]
With ACCS (Advanced Climate Control System)
Without ACCS (Advanced Climate Control System)
NOTE:
When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V
or less, the setting of the inlet port memory function may be cancelled.
Exhaust Gas/Outside Odor Detecting Sensor Sensitivity Adjustment Function
INFOID:0000000009652544
DESCRIPTION
Sensitivity of exhaust gas/outside odor detecting sensor is adjustable for 2 steps of high and low. This function
is used when sensitivity of sensor is different from customer
′
s sense of smell.
HOW TO SET
1.
Starts on board self-diagnosis STEP 5 mode (Each sensor recognition temperature check; “51” or “52” is
indicated on front A/C control display).
2.
Press fan switch (up: +) twice and check that “7” is indicated on front A/C control display.
3.
After approximately 3 seconds, the exhaust gas/outside odor detecting sensor sensitivity adjustment func-
tion can be available.
4.
Press temperature control switch (driver side) to select the setting as per the following.
NOTE:
When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V
or less, the setting of the exhaust gas/outside odor detecting sensor sensitivity adjustment function may be
cancelled.
AUTO Intake Switch Interlocking Movement Change Function
INFOID:0000000009652545
DESCRIPTION
Condition for interlocking movement of AUTO intake switch and A/C switch can be changed. It is possible to
set the system not to receive switch operation of AUTO intake switch when A/C switch is OFF so that the
Switch
Switch indicator
Setting
AUTO intake switch
OFF
Do not perform the memory of instruction FRE (Initial setting)
ON
Perform the memory of instruction FRE
Intake switch
OFF
Do not perform the memory of instruction REC
ON
Perform the memory of instruction REC (Initial setting)
Switch
Switch indicator
Setting
FRE switch
OFF
Do not perform the memory of instruction FRE (Initial setting)
ON
Perform the memory of instruction FRE
REC switch
OFF
Do not perform the memory of instruction REC
ON
Perform the memory of instruction REC (Initial setting)
Display
Setting
75
More sensitive setting than display 74 setting (the change to REC is earlier than display 74 operation)
74
More sensitive setting than normal setting (the change to REC is earlier than normal operation)
73
Normal (Initial setting)
72
Less sensitive setting than normal setting (the change to REC is later than normal operation)
71
Less sensitive setting than display 72 setting (the change to REC is later than display 72 operation)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст