Nissan Quest E52. Instruction — part 210
BCS
INSPECTION AND ADJUSTMENT
BCS-83
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000009651715
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NATS) (if equipped).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work Proce-
dure
INFOID:0000000009651716
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
BCS-98, "Removal and Installation"
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Instruction selection” to write
vehicle specification. Refer to
BCS-84, "CONFIGURATION (BCM) : Work Procedure"
.
>> GO TO 4.
4.
INITIALIZE BCM (NATS) (IF EQUIPPED)
Perform BCM initialization. (NATS)
>> WORK END
CONFIGURATION (BCM)
BCS-84
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
CONFIGURATION (BCM) : Description
INFOID:0000000009651717
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
NOTE:
Instruction setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
CONFIGURATION (BCM) : Work Procedure
INFOID:0000000009651718
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “CONFIGURATION” of BCM.
When writing saved data>>GO TO 2.
When writing instructionly>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file”.
>> WORK END
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
CONSULT Configuration
1.
Select "WRITE CONFIGURATION - Instruction selection".
2.
Identify the correct model and configuration list. Refer to
BCS-85, "CONFIGURATION (BCM) : Configura-
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
NOTE:
If items are not displayed, touch “SETTING”. Refer to
BCS-85, "CONFIGURATION (BCM) : Configuration
for written items and setting value.
4.
Select "SETTING".
CAUTION:
Make sure to select “SETTING” even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.
5.
When "COMMAND FINISHED", select "END".
>> GO TO 4.
Function
Description
READ CONFIGURATION
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Instruction selection
Writes the vehicle configuration with instruction selection.
WRITE CONFIGURATION - Config file
Writes the vehicle configuration with saved data.
BCS
INSPECTION AND ADJUSTMENT
BCS-85
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
CONFIGURATION (BCM) : Configuration list
INFOID:0000000009651719
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
⇔
: Items which confirm vehicle specifications
SETTING ITEM
NOTE
Items
Setting value
CAN CONNECTION UNIT
WITHOUT
⇔
MODE13
⇔
MODE15
• WITHOUT: Without automatic sliding door system and au-
tomatic back door system
• MODE13: With automatic sliding door system and automat-
ic back door system
• MODE15: With automatic sliding door system, and without
automatic back door system
AUTO LIGHT
WITH
⇔
WITHOUT
—
DTRL
WITH
⇔
WITHOUT
• WITH: With daytime running light system
• WITHOUT: Without daytime running light system
BCS-86
< BASIC INSPECTION >
SHIPPING MODE CANCEL OPERATION
SHIPPING MODE CANCEL OPERATION
Description
INFOID:0000000010012595
SYSTEM DIAGRAM
DESCRIPTION
• The combination meter transmits meter CAN signal*
1
to BCM via CAN communication, when the extended
storage fuse switch is ON.
• BCM switches the status (shipping mode or normal mode) by itself according to the meter CAN signal*
1
from
combination meter, and transmits shipping mode status signal to combination meter via CAN communica-
tion.
• The combination meter displays extended storage fuse warning message*
2
on the information display, and
turns the turn signal indicator lamp (LH/RH) ON, when BCM is in shipping mode.
• BCM control functions are limited in shipping mode. Refer to
*1: Odometer signal, wake up signal and each signal.
*2: When shipping mode function operates, “SHIPPING MODE ON PUSH STORAGE FUSE” is displayed.
Work Procedure
INFOID:0000000010012596
1.
SHIPPING MODE CANCEL OPERATION
1.
Turn ignition switch OFF.
2.
Push in (switch on) the extended storage fuse switch. Refer to
3.
Turn ignition switch ON.
4.
Turn ignition switch OFF and wait at least 2 seconds.
>> GO TO 2.
2.
SHIPPING MODE CANCEL CHECK
1.
Turn ignition switch ON.
2.
Check that extended storage fuse warning message is not displayed on odometer display.
>> WORK END
JMMIA1345GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст