Nissan Quest E52. Instruction — part 417
DLK-382
< SYMPTOM DIAGNOSIS >
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-
ATE
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE
Diagnosis Procedure
INFOID:0000000009649346
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-94, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “Unlock Only”, “Lock Only” or “Lock/Unlock” in “AUTOMATIC LOCK/UNLOCK SELECT”.
2.
CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-94, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “P RANGE” in “AUTOMATIC DOOR LOCK SELECT”.
3.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-94, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “MODE 2” or “MODE 4” in “AUTOMATIC DOOR UNLOCK SELECT”.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-98, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
HAZARD AND HORN REMINDER DOES NOT OPERATE
DLK-383
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD AND HORN REMINDER DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009649347
1.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.
3.
Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to
DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.
2.
CHECK “HORN WITH KEYLESS LOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “HORN WITH KEYLESS LOCK” in “WORK SUPPORT” mode.
3.
Check the “HORN WITH KEYLESS LOCK” in “WORK SUPPORT”.
Refer to
DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set the “On” in “HORN WITH KEYLESS LOCK”.
3.
CHECK HAZARD FUNCTION
Check hazard function.
Refer to
DLK-279, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK HORN FUNCTION
Check horn function.
Refer to
SEC-120, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-98, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DLK-384
< SYMPTOM DIAGNOSIS >
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009649348
1.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.
3.
Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to
DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.
2.
CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.
3.
Check the “ANS BACK I-KEY LOCK”setting in “WORK SUPPORT”.
Refer to
DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set the “Horn Chirp” or “Buzzer” in “ANS BACK I-KEY LOCK”.
3.
CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.
3.
Check the “ANS BACK I-KEY UNLOCK” setting in “WORK SUPPORT”.
Refer to
DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set the “On” in “ANS BACK I-KEY UNLOCK”.
4.
CHECK HAZARD FUNCTION
Check hazard function.
Refer to
DLK-279, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to
DLK-273, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-98, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
KEY REMINDER FUNCTION DOES NOT OPERATE
DLK-385
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY REMINDER FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009649349
1.
CHECK DTC WITH BCM
Check that DTC is not detected with BCM.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
2.
CHECK “ANTI KEY LOCK IN FUNCTI” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT” mode.
3.
Check “ANTI KEY LOCK IN FUNCTI” setting in “WORK SUPPORT”.
Refer to
DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “On” in “ANTI KEY LOCK IN FUNCTI”.
3.
CHECK DOOR SWITCH
Check door switch
Refer to
DLK-241, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Instrument center: Refer to
.
.
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK UNLOCK SENSOR
Check unlock sensor.
Refer to
DLK-259, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-98, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст