Nissan Quest E52. Instruction — part 906
MWI
METER SYSTEM
MWI-29
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• The combination meter judges showing/hiding of “engine oil warning”, according to the signals below:
Other (Maintenance)
• When all the following operating conditions are satisfied, the combination meter displays a other warning on
the information display by an interrupt.
• The combination meter judges showing/hiding of “other warning”, according to the signals below:
Meter Illumination Level Indication
When receiving the following signals, the combination meter causes an interrupt on the information display to
indicate an illumination level.
WARNING CHECK INDICATION
• The combination meter can cause an interrupt on the information display to indicate a warning, based on
signals received from each unit and switch.
• The indicated warning can be checked with “WARNING” during the satisfaction of an interrupt indication
condition for each warning.
SETTING
Warning indication timing and time can be set.
Alert
Setting values for travel time, and low ambient temperature can be adjusted to meet the user's needs.
Maintenance
Setting values for engine oil, oil filter, tire, and other maintenance items can be adjusted to meet the user's
needs.
Operating condition
Ignition switch
ON
Mileage
More than value set in “SETTING”
Signal name
Signal Path
Ignition signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination
meter
Operating condition
Ignition switch
ON
Mileage
More than value set in “SETTING”
Signal name
Signal Path
Ignition signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination
meter
Signal name
Signal Path
Ignition signal
—
Illumination control switch signal (+)
Illumination control switch
Combination meter
Illumination control switch signal (
−
)
Setting item
Setting range
Setting unit
Alert
Timer
No setting, 0.5 h - 6 h
0.5 h
ICY
ON/OFF
—
MWI-30
< SYSTEM DESCRIPTION >
METER SYSTEM
Options
Setting values for language, unit, and effect items can be adjusted to meet the user's needs.
Settings-reject Indication
• Regarding settings-reject indications, “SETTING CAN BE OPERATED WHEN STOPPED” is shown on the
information display when indication conditions are satisfied.
• When reaching 5 km/h (3.1 MPH) after accelerating from a stopping condition, a settings-reject indication is
displayed.
• When reaching less than 2 km/h (1.2 MPH) after decelerating from 5 km/h (3.1 MPH), a settings-reject indi-
cation is cancelled to allow settings.
• The combination meter judges a vehicle condition based on the following signals and displays a settings-
reject indication on the information display.
Setting item
Setting range
Maintenance
Engine oil
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Oil filter
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Tire
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Other
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Setting item
Options
Language
ENGLISH
FRANCAISE
Unit
miles, MPG,
°
F
km, l/100 km,
°
C
Effect
ON/OFF
Signal name
Signal Path
Ignition signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
MWI
METER SYSTEM
MWI-31
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
TIMING CHART
JSNIA4356GB
MWI-32
< SYSTEM DESCRIPTION >
COMPASS
COMPASS
System Description
INFOID:0000000009651481
DESCRIPTION
• This electronic compass is able to display 8 primary directions: N, NE, E, SE, S, SW, W, NW.
• The inside mirror switch is used to operate the compass.
Switch Operation
• All standard compasses determine direction relative to magnetic north, however, this electronic compass is
designed to display direction relative to true north.
• The difference between magnetic north and true north varies from place to place across the surface of the
earth.
• This electronic compass must be “told” approximately where it is on the earth’s surface so that the magnetic
north reading can be properly converted into a true north display.
• To tell the electronic compass where it’s at, the earth is separated into numbered “Zone Variances”. The
zone variance number in which the compass is to function must be entered into this electronic compass.
• Each zone is magnetically about 4.2
°
wide. Typically, anything under a 22.5
°
total zone change is not noticed
on the electronic compass display. However, if a change over 22.5
°
occurs, a reading may be off by one or
more primary directions.
• On long trips, the vehicle may leave its original zone and enter one or more new zones. Generally, you do
not need to reset the compass zone if you travel between 3 or 4 zones, such as business travel or vacation.
The typical driver will not notice any difference on the display within 3 or 4 zones. However, if the vehicle is
“permanently” moved to a new location, it is recommended that the compass zone be reset.
1
: Compass switch
2
: Compass display
SKIB8868E
Press
Compass is turned ON/OFF
Press and hold
(for 3- 9 sec.)
Compass display turns to zone variation change
mode
Press and hold (for more
than 9 sec.)
Compass display turns to calibration mode
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст