Nissan Quest E52. Instruction — part 220
BR-24
< REMOVAL AND INSTALLATION >
BRAKE PIPING
REAR : Hydraulic Piping
INFOID:0000000009651821
REAR : Removal and Installation
INFOID:0000000009651822
REMOVAL
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied
with, brake fluid may splash.
• If the brake fluid adheres to the brake caliper assembly and disc rotor, quickly wipe it off.
1.
Remove tires with power tool.
2.
Drain brake fluid. Refer to
.
3.
Loosen the flare nut (1) with a flare nut wrench (A) and separate
the brake tube (2) from the brake hose (3).
CAUTION:
• Never scratch the flare nut and the brake tube.
• Never bend sharply, twist or strongly pull out the brake
hoses and tubes.
• Cover open end of brake tubes and hoses when discon-
necting to prevent entrance of dirt.
1.
ABS actuator and electric unit (con-
trol unit)
2.
Front disc brake
3.
Master cylinder assembly
4.
Brake booster
5.
Connector
6.
Rear disc brake
A.
Brake tube
B.
Brake hose
: Flare nut
: Union bolt
JSFIA0959ZZ
JSFIA0561ZZ
BRAKE PIPING
BR-25
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
4.
Remove the union bolt (1) and copper washers (2), and remove
the brake hose (3) from the brake caliper assembly.
5.
Remove the lock plate (4), and remove brake hose.
INSTALLATION
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied
with, brake fluid may splash.
• If the brake fluid adheres to the brake caliper assembly and disc rotor, quickly wipe it off.
1.
Assemble the union bolt (1) and the copper washer (2) to the
brake hose.
CAUTION:
Never reuse the copper washer.
2.
Align the brake hose L-pin (A) with the brake caliper assembly
hole (B), and tighten the union bolt to the specified torque.
3.
Install the brake tube (2) to the brake hose (1), temporarily
tighten the flare nut (3) by hand until it does not rotate further,
and fix the brake hose with the lock plate (4).
CAUTION:
Check that all brake hose and brake tube are not twisted
and bent.
4.
Tighten the flare nut to the specified torque with a crowfoot (A)
and torque wrench (B).
CAUTION:
Never scratch the flare nut and the brake tube.
5.
Perform the air bleeding. Refer to
6.
Install tires with power tool. Refer to
.
7.
Perform inspection after installation. Refer to
.
REAR : Inspection
INFOID:0000000009651823
INSPECTION AFTER INSTALLATION
JSFIA0562ZZ
JSFIA0563ZZ
JSFIA0564ZZ
JPFIA0001ZZ
BR-26
< REMOVAL AND INSTALLATION >
BRAKE PIPING
1.
Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no looseness
at connections.
2.
Depress the brake pedal with a force of 785 N (80 kg, 176 lb) and hold down the pedal for approximately
5 seconds with the engine running. Check for any fluid leakage.
CAUTION:
Retighten the applicable connection to the specified torque and repair any abnormal (damaged,
worn or deformed) part if any brake fluid leakage is present.
BRAKE MASTER CYLINDER
BR-27
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE MASTER CYLINDER
Exploded View
INFOID:0000000009651824
Removal and Installation
INFOID:0000000009651825
REMOVAL
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake tube. If this is not complied with, brake fluid
may splash.
1.
Perform inspection before removal. Refer to
2.
Depress the brake pedal several times to release the vacuum pressure from the brake booster.
3.
Drain brake fluid. Refer to
4.
Disconnect the brake fluid level switch harness connector.
1.
Reservoir cap
2.
Reservoir tank
3.
Reservoir tank bracket
4.
Clamp
5.
Hose
6.
Bracket
7.
Clamp
8.
Cylinder body
9.
Pin
10.
O-ring
11.
Grommet
12.
Sub tank
A.
Paint mark
: Apply polyglycol ether based lubricant.
: Apply brake fluid.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA0961GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст