Nissan Quest E52. Instruction — part 1005
PWO-8
< REMOVAL AND INSTALLATION >
[POWER SOCKET]
POWER SOCKET
Note the following, and install in the reverse order of removal.
Align the cut outs of inner socket, ring and luggage side lower fin-
isher (LH).
A
: Cut out
JPMIA1614ZZ
PWO
SERVICE DATA AND SPECIFICATIONS (SDS)
PWO-9
< SERVICE DATA AND SPECIFICATIONS (SDS)
[POWER SOCKET]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Power Socket
INFOID:0000000009651870
Rated voltage
DC 12 V
Maximum electric capacity
120 W or less (Total)
Maximum current
10 A or less (Total)
PWO-10
< PRECAUTION >
[AC 120 V OUTLET]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009651871
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing Battery Terminal
INFOID:0000000009981909
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
PWO
COMPONENT PARTS
PWO-11
< SYSTEM DESCRIPTION >
[AC 120 V OUTLET]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009651872
COMPONENT PARTS DESCRIPTION
AC 120 V Outlet Main Switch
INFOID:0000000009651873
The operation of the switch enables the inverter unit to activate/inac-
tivate and turn ON/OFF AC 120 V output.
A.
Luggage room finisher RH remove
condition
JSMIA0710ZZ
No.
Component
Function
1.
AC 120 V outlet main switch
PWO-11, "AC 120 V Outlet Main Switch"
2.
AC 120 V outlet
3.
Inverter unit
JSMIA0425ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст