Nissan Quest E52. Instruction — part 162
AV
INSPECTION AND ADJUSTMENT
AV-527
< BASIC INSPECTION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
AVM: Around view monitor
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure
INFOID:0000000009942945
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-631, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Select “Configuration” or “After Replace ECU”, and write the vehicle specification saved in CONSULT to
around view monitor control unit.
>> GO TO 6.
4.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-631, "Removal and Installation"
>> GO TO 5.
5.
WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Select “Instruction Configuration”, and write the vehicle specification to around view monitor control unit.
NOTE:
Around view monitor control unit does not have any setting items. Selection of items on “Manual Configura-
tion” screen is not required.
>> GO TO 6.
6.
PERFORM SELF-DIAGNOSIS
CONSULT Self Diagnostic Result
Perform self-diagnosis of CONSULT, and check whether or not DTC U1305 is detected.
Is DTC U1305 detected?
MANUAL SETTING ITEM
Detail
Items
Setting value
STEERING
LHD
LHD models
RHD
RHD models
CAMERA SYSTEM
NONE/AVM
Without camera system or with around view monitor system
REAR CAMERA
With rear view monitor system
REAR+SIDE
With rear view monitor system and front-side view monitor function
SOUND SYSTEM
BASE
Without BOSE system
BOSE
With BOSE system
AV-528
< BASIC INSPECTION >
[BOSE AUDIO WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
>> GO TO 5.
>> GO TO 7.
7.
OPERATION CHECK
Check that the operation of the around view monitor control unit and camera images (fixed guide lines and
predictive course lines) are normal.
>> WORK END
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Description
INFOID:0000000009942946
Adjust the center position of the predictive course line of the rear view monitor if it is shifted.
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Work Procedure
INFOID:0000000009942947
1.
DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description
INFOID:0000000009942948
• Calibration must be performed after removing/replacing the cameras, removing parts (e.g. front grille, door
mirror, and others) mounted on the cameras, or replacing the Around view monitor control unit.
• The use of CONSULT is required to perform calibration or writing of calibration results to the Around view
monitor control unit.
• Align the white lines on the road near the vehicle at the boundary of each camera image by this camera cal-
ibration. The white lines far from the vehicle may not be aligned at the boundary of each camera image. The
farther the line, the greater the difference is.
CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure
INFOID:0000000009942949
CALIBRATION FLOWCHART
AV
INSPECTION AND ADJUSTMENT
AV-529
< BASIC INSPECTION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Following the flowchart shown in the figure, perform the calibration.
NOTE:
View in the incomplete calibration state is indicated by “
” on the
around view monitor.
CALIBRATION PROCEDURE
1.
AROUND VIEW MONITOR SCREEN CONFIRMATION
Check that there is no indication of “Incomplete calibration”.
Is the “Incomplete calibration” display visible?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK THAT AROUND VIEW MONITOR CONTROL UNIT IS REPLACED
Check that the around view monitor control unit is replaced.
Is the around view monitor control unit replaced?
YES
>> GO TO 3.
NO
>> GO TO 5.
JSNIA4210GB
JSNIA4606ZZ
JSNIA4606ZZ
AV-530
< BASIC INSPECTION >
[BOSE AUDIO WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
3.
CANCEL THE INDICATION OF INCOMPLETE CALIBRATION (PERFORM THIS ONLY AFTER REPLAC-
ING AROUND VIEW MONITOR CONTROL UNIT.)
CONSULT work support
1.
On the CONSULT screen, touch “CALIBRATING CAMERA IMAGE (FRONT CAMERA)”, “CALIBRATING
CAMERA IMAGE (PASS-SIDE CAMERA)”, “CALIBRATING CAMERA IMAGE (DR-SIDE CAMERA)”, or
“CALIBRATING CAMERA IMAGE (REAR CAMERA)” to accept the selection.
NOTE:
To cancel the indication of Incomplete calibration, select items based on the target camera.
2.
On the adjustment screen of each camera, touch “APPLY” but-
ton. After this, touch “OK” button.
CAUTION:
• Never perform operations other than those mentioned
above.
• Never perform “Initialize Camera Image Calibration”.
3.
Display the around view monitor screen to check that there is no
errors, such as deviations among the camera images.
Is there a malfunction?
YES
>> Calibration end
NO
>> GO TO 1.
4.
PERFORM SIMPLIFIED CONFIRMATION/ADJUSTMENT BY “FINE TUNING OF BIRDS-EYE VIEW”
1.
Put target line 1 on the ground beside each axle using packing tape, etc.
2.
Put target lines 2 equal to the vehicle total length + approximately 1.0 m (39.3 in) from the vehicle side
(right and left) at approximately 30 cm (11.8 in) away from the vehicle (make the line as parallel with the
vehicle as possible)
Preparation of simplified target line
3.
CONSULT work support
Touch “FINE TUNING OF BIRDS-EYE VIEW” on the CONSULT screen.
4.
On the CONSULT screen, touch “SELECT” button to select right or left camera and perform camera cali-
bration as instructed below:
-
If the marker on the screen deviates from Target line 1, touch “AXIS X” button and “AXIS Y” button to
adjust so that the marker is placed on the Target line 1.
-
If Target line 2 is misaligned among the cameras, adjust each camera image to bring Target line 2 into a
straight line.
CAUTION:
Never adjust the front camera and rear camera. Only adjust the right and left cameras.
JSNIA4212ZZ
JSNIA0927ZZ
1.
Target lines 1
2.
Target lines 2
A.
Approx. 30 cm (11.8 in)
B.
Approx. 1.0 m (39.3 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст