Nissan Quest E52. Instruction — part 642
EXL-172
< BASIC INSPECTION >
[HALOGEN TYPE]
DIAGNOSIS AND REPAIR WORK FLOW
1.
GET INFORMATION FOR SYMPTOM
1.
Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2.
Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is detected.
-
Record DTC and freeze frame data (Print them out using CONSULT.)
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to DTC INSPECTION PRIORITY CHART, and determine trouble diag-
nosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Instruction. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Check according to
GI-42, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES
>> GO TO 7.
NO
>> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
DIAGNOSIS AND REPAIR WORK FLOW
EXL-173
< BASIC INSPECTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-42, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
EXL-174
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
HEADLAMP (HI) CIRCUIT
DTC/CIRCUIT DIAGNOSIS
HEADLAMP (HI) CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000009653149
1.
CHECK HEADLAMP (HI) OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp (HI) is turned ON.
NOTE:
ON/OFF is repeated 1 second each.
Is the inspection result normal?
YES
>> Headlamp (HI) circuit is normal.
NO
>> Refer to
EXL-174, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000009653150
1.
CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect headlamp high connector.
3.
Turn ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK HEADLAMP (HI) OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and headlamp high harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
Hi
: Headlamp (HI) ON
Off
: Headlamp (HI) OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E345
89
Ground
EXTERNAL
LAMPS
Hi
Battery voltage
Off
0 V
LH
90
Hi
Battery voltage
Off
0 V
IPDM E/R
Headlamp high
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
89
E326
1
Existed
LH
90
E325
HEADLAMP (HI) CIRCUIT
EXL-175
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NO
>> Repair or replace harness.
3.
CHECK HEADLAMP (HI) FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 4.
4.
CHECK HEADLAMP (HI) SHORT CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
5.
CHECK HEADLAMP (HI) GROUND OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect headlamp high connector.
3.
Check continuity between headlamp high harness connector and ground.
Is the inspection result normal?
YES
>> Replace headlamp (HI) bulb. (Bulb socket is abnormal.)
NO
>> Repair or replace harness.
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000009653151
1.
CHECK HEADLAMP (HI) OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp (HI) is turned ON.
NOTE:
ON/OFF is repeated 1 second each.
Is the inspection result normal?
YES
>> Headlamp (HI) circuit is normal.
NO
>> Refer to
EXL-176, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
Unit
Location
Fuse No.
Capacity
Headlamp HI (RH)
IPDM E/R
#55
10 A
Headlamp HI (LH)
#54
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
89
Not existed
LH
90
Headlamp high
Ground
Continuity
Connector
Terminal
RH
E326
2
Existed
LH
E325
Hi
: Headlamp (HI) ON
Off
: Headlamp (HI) OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст