Nissan Quest E52. Instruction — part 623
EXL-96
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000009653076
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009653077
1.
CHECK COMBINATION SWITCH
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL LO REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
3.
HEADLAMP (LO) CIRCUIT INSPECTION
Check headlamp (LO) circuit. Refer to
EXL-66, "Component Function Check"
Is the inspection result normal?
YES
>> Refer to
GI-42, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
On
OFF
Off
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
EXL-97
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
Description
INFOID:0000000009653078
The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009653079
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Lighting switch
1ST
On
OFF
Off
EXL-98
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000009653080
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009653081
1.
CHECK FRONT FOG LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT FOG LAMP SHORT CIRCUIT
1.
Disconnect front fog connector and IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning part.
4.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “FR FOG REQ” of IPDM E/R data monitor item.
2.
With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 5.
NO
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
5.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
EXL-81, "Component Function Check"
.
Is the inspection result normal?
YES
>> Refer to
GI-42, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning part.
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#58
15 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
86
Not existed
LH
87
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 2ND)
ON
On
OFF
Off
HEADLAMP AIMING ADJUSTMENT
EXL-99
< PERIODIC MAINTENANCE >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000009653082
preparation before adjusting
NOTE:
• for details, refer to the regulations in your own country.
• perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
before performing aiming adjustment, check the following.
• adjust the tire pressure to the specification.
• fill with fuel, engine coolant and each oil.
• maintain the unloaded vehicle condition. (remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
do not remove the temporary tire, jack and on-vehicle tool.
• wipe out dirt on the headlamp.
CAUTION:
never use organic solvent (thinner, gasoline etc.)
• ride alone on the driver seat.
aiming adjustment screw
JMLIA2181ZZ
A.
Headlamp RH HI/LO (UP/DOWN)
adjustment screw
B.
Headlamp LH HI/LO (UP/DOWN)
adjustment screw
: Vehicle center
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст