Nissan Quest E52. Instruction — part 971
PG-104
< BASIC INSPECTION >
FUSIBLE LINK INSPECTION
FUSIBLE LINK INSPECTION
How To Check
INFOID:0000000009651789
A melted fusible link can be detected either by visual inspection or by
feeling with finger tip. If its condition is questionable, use circuit
tester or test lamp.
CAUTION:
• If fusible link should melt, it is possible that critical circuit
(power supply or large current carrying circuit) is shorted. In
such a case, carefully check and eliminate cause of malfunc-
tion.
• Never wrap outside of fusible link with vinyl tape. Important:
Never let fusible link touch any other wiring harness, vinyl or
rubber parts.
1
:Fusible link
JPMIA1291ZZ
PG
BATTERY
PG-105
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
REMOVAL AND INSTALLATION
BATTERY
Exploded View
INFOID:0000000009651790
Removal and Installation
INFOID:0000000009651791
REMOVAL
1.
Remove air duct (inlet). Refer to
EM-26, "Removal and Installation"
2.
Disconnect the battery cable from the negative terminal.
CAUTION:
To prevent damage to the parts, disconnect the battery cable from the negative terminal first.
3.
Remove the nut and bolt and remove the ECM bracket from the battery fix frame.
4.
Remove cover of battery positive terminal.
5.
Disconnect the battery cable from the positive terminal.
6.
Remove battery fix frame mounting nuts and battery fix frame.
7.
Remove battery.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To install the battery, carefully read the following instructions.
• To prevent damage to the parts, connect the battery cable to the positive terminal first.
• After connecting battery cables, to securely supply battery voltage, ensure that they are tightly
clamped to battery terminals for good contact.
• To securely supply battery voltage, check battery terminal for poor connection caused by corrosion.
Reset electronic systems as necessary. Refer to
GI-58, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Required Procedure After Battery Disconnection"
1
: Battery fix frame
: N·m (kg-m, in-lb)
JPMIA1608GB
PG-106
< REMOVAL AND INSTALLATION >
BATTERY TERMINAL WITH FUSIBLE LINK
BATTERY TERMINAL WITH FUSIBLE LINK
Exploded View
INFOID:0000000009651792
Removal and Installation
INFOID:0000000009651793
REMOVAL
1.
Disconnect the battery cable from the negative terminal. Refer to
.
CAUTION:
To prevent damage to the parts, disconnect the battery cable from the negative terminal first.
2.
Remove cover of battery positive terminal.
3.
Disconnect the battery cable from the positive terminal. Refer to
.
4.
Remove harness mounting nut and battery terminal with fusible link mounting nut.
5.
Disconnect harness connector and remove battery terminal with fusible link.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To prevent damage to the parts, connect the battery cable to the positive terminal first.
1
: Battery terminal with fusible link
2
: Harness connector
: N·m (kg-m, ft-lb)
JPMIA1609GB
PG
BATTERY CURRENT SENSOR
PG-107
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BATTERY CURRENT SENSOR
Exploded View
INFOID:0000000009651794
Removal and Installation
INFOID:0000000009651795
REMOVAL
1.
Disconnect the battery cable from the negative terminal. Refer to
.
2.
Disconnect the battery current sensor connector.
3.
Remove the battery current sensor mounting nut.
4.
Remove the battery current sensor from battery cable.
INSTALLATION
Install in the reverse order of removal.
1
: Battery current sensor
(with battery temperature sensor)
2
: Harness connector
: N·m (kg-m, ft-lb)
JSMIA0700GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст