Nissan Quest E52. Instruction — part 989
PWC-68
< REMOVAL AND INSTALLATION >
[FRONT WINDOW ANTI-PINCH]
POWER WINDOW MAIN SWITCH
REMOVAL AND INSTALLATION
POWER WINDOW MAIN SWITCH
Removal and Installation
INFOID:0000000009653343
REMOVAL
1.
Remove the power window main switch finisher. Refer to
14, "Removal and Installation"
.
2.
Remove power window main switch (1) from power window
main switch finisher (2) using a remover tool (A).
NOTE:
The same procedure is also performed for front power window
switch (passenger side).
INSTALLATION
Install in the reverse order of removal.
NOTE:
If power window main switch or front power window (passenger side) is replaced or is removed, it is necessary
to perform the initialization procedure.
Refer to
: Pawl
JMKIA8164ZZ
SLIDING DOOR POWER WINDOW SWITCH
PWC-69
< REMOVAL AND INSTALLATION >
[FRONT WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
SLIDING DOOR POWER WINDOW SWITCH
Removal and Installation
INFOID:0000000009653344
REMOVAL
1.
Remove sliding door finisher. Refer to
.
2.
Remove screw (A), disconnect pawls from sliding door finisher
(1), and then remove power window switch finisher (2).
3.
Remove power window switch (1) from power window switch fin-
isher (2) using a remover tool (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA8165ZZ
: Pawl
JMKIA8166ZZ
PWC-70
< PRECAUTION >
[DRIVER SIDE WINDOW ANTI-PINCH]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009653345
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing Battery Terminal
INFOID:0000000009962077
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
COMPONENT PARTS
PWC-71
< SYSTEM DESCRIPTION >
[DRIVER SIDE WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009653346
A.
View with front door finisher removed B.
View with sliding door finisher removed
No.
Component parts
Description
1.
BCM
• Supplies power supply to power window switch.
• Controls retained power.
Refer to
BCS-4, "BODY CONTROL SYSTEM : Component Parts Location"
for detailed installation location.
2.
Power window main switch
Refer to
PWC-72, "Power Window Main Switch"
.
3.
Front power window motor (driver side)
Refer to
PWC-72, "Front Power Window Motor (Driver Side)"
.
4.
Front door switch (driver side)
Detects door open/close condition and transmits to BCM. Refer to
JMKIA8163ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст