Nissan Quest E52. Instruction — part 450
EC-10
< PRECAUTION >
[VQ35DE]
PRECAUTIONS
General Precautions
INFOID:0000000009650917
• Always use a 12 volt battery as power source.
• Never attempt to disconnect battery cables while engine is
running.
• Before connecting or disconnecting the ECM harness con-
nector, turn ignition switch OFF and disconnect negative bat-
tery cable. Failure to do so may damage the ECM because
battery voltage is applied to ECM even if ignition switch is
turned OFF.
• Before removing parts, turn ignition switch OFF and then dis-
connect battery ground cable.
• Never disassemble ECM.
• If a battery cable is disconnected, the memory will return to the ECM value.
The ECM will now start to self-control at its initial value. Thus, engine operation can vary slightly in
this case. However, this is not an indication of a malfunction. Never replace parts because of a slight
variation.
• If the battery is disconnected, the following emission-related diagnostic information will be lost
within 24 hours.
- Diagnostic trouble codes
- 1st trip diagnostic trouble codes
- Freeze frame data
- 1st trip freeze frame data
- System readiness test (SRT) codes
- Test values
• When connecting ECM harness connector, fasten (B) it
securely with a lever (1) as far as it will go as shown in the fig-
ure.
- ECM (2)
- Loosen (A)
• When connecting or disconnecting pin connectors into or
from ECM, never damage pin terminals (bends or break).
Check that there are not any bends or breaks on ECM pin ter-
minal, when connecting pin connectors.
• Securely connect ECM harness connectors.
A poor connection can cause an extremely high (surge) volt-
age to develop in coil and condenser, thus resulting in dam-
age to ICs.
• Keep engine control system harness at least 10 cm (4 in) away
from adjacent harness, to prevent engine control system mal-
functions due to receiving external noise, degraded operation
of ICs, etc.
• Keep engine control system parts and harness dry.
SEF289H
PBIB2947E
PBIB0090E
PRECAUTIONS
EC-11
< PRECAUTION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• Before replacing ECM, perform ECM Terminals and Reference
Value inspection and check ECM functions properly. Refer to
.
• Handle mass air flow sensor carefully to avoid damage.
• Never clean mass air flow sensor with any type of detergent.
• Never disassemble electric throttle control actuator.
• Even a slight leakage in the air intake system can cause seri-
ous incidents.
• Never shock or jar the camshaft position sensor (PHASE),
crankshaft position sensor (POS).
• After performing each TROUBLE DIAGNOSIS, perform DTC
Confirmation Procedure or Component Function Check.
The DTC should not be displayed in the DTC Confirmation
Procedure if the repair is completed. The Component Func-
tion Check should be a good result if the repair is completed.
• When measuring ECM signals with a circuit tester, never allow
the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.
MEF040D
JSBIA1315ZZ
SEF348N
EC-12
< PRECAUTION >
[VQ35DE]
PRECAUTIONS
• B1 indicates bank 1, B2 indicates bank 2 as shown in the fig-
ure.
• Never operate fuel pump when there is no fuel in lines.
• Tighten fuel hose clamps to the specified torque.
• Never depress accelerator pedal when starting.
• Immediately after starting, never rev up engine unnecessarily.
• Never rev up engine just prior to shutdown.
• When installing C.B. ham radio or a mobile phone, be sure to
observe the following as it may adversely affect electronic
control systems depending on installation location.
- Keep the antenna as far as possible from the electronic con-
trol units.
- Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Never let them run parallel for a long distance.
- Adjust the antenna and feeder line so that the standing-wave
ratio can be kept smaller.
- Be sure to ground the radio to vehicle body.
SEC893C
SEF709Y
SEF708Y
PREPARATION
EC-13
< PREPARATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009650918
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009650919
Tool number
(Kent-Moore No.)
Tool name
Description
(J-44321)
Fuel pressure gauge
kit
Checks fuel pressure
(J-44321-6)
Fuel pressure adapter
Connects fuel pressure gauge to quick connector
type fuel lines
LEC642
LBIA0376E
Tool name
(Kent-Moore No.)
Description
(J-45488)
Quick connector re-
lease
Removes fuel tube quick connectors in engine
room
Leak detector
i.e.: (J-41416)
Locates the EVAP leakage
EVAP service port
adapter
i.e.: (J-41413-OBD)
Applys positive pressure through EVAP service
port
PBIC0198E
S-NT703
S-NT704
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст