Nissan Quest E52. Instruction — part 684
FRONT STABILIZER
FSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000009650675
Removal and Installation
INFOID:0000000009650676
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Remove exhaust front tube. Refer to
EX-6, "Removal and Installation"
3.
Remove wheel sensor harness from strut assembly. Refer to
BRC-119, "FRONT WHEEL SENSOR :
.
4.
Separate steering outer socket from steering knuckle. Refer to
ST-22, "Removal and Installation"
.
5.
Remove stabilizer connecting rod.
6.
Remove drive shaft (right side). Refer to
FAX-19, "RIGHT SIDE : Removal and Installation"
.
7.
Remove mounting bolts (
) of stabilizer clamp, and then
remove stabilizer clamp and stabilizer bushing from front sus-
pension member.
8.
Remove stabilizer bar.
9.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Stabilizer clamp
2.
Stabilizer bushing
3.
Stabilizer bar
4.
Front suspension member
5.
Stabilizer connecting rod
: N·m (kg-m, ft-lb)
JPEIA0164GB
WEIA0182E
FSU-16
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
• Install stabilizer clamp and stabilizer bush with notch (A) and slit
(B) faced forward of the vehicle (
).
• To install stabilizer connecting rod (1), tighten the mounting nut
with the hexagonal part (A) on the stabilizer connecting rod side
fixed.
• Perform final tightening of bolts and nuts at the vehicle installation
position (rubber bushing), under unladen conditions with tires on
level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009650677
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
BRC-119, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
(with VDC).
JPEIA0058ZZ
JPEIA0252ZZ
FRONT SUSPENSION MEMBER
FSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000009650678
Removal and Installation
INFOID:0000000009650679
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Remove the engine and the transaxle assembly from the vehicle together with the front suspension mem-
ber. Refer to
EM-56, "Removal and Installation"
.
3.
Remove the following parts from front suspension member.
• Engine assembly: Refer to
EM-56, "Removal and Installation"
.
• Transaxle assembly: Refer to
TM-174, "Removal and Installation"
.
• Steering gear assembly: Refer to
ST-22, "Removal and Installation"
.
• Steering hydraulic line: Refer to
• Stabilizer bar: Refer to
FSU-15, "Removal and Installation"
FSU-13, "Removal and Installation"
.
4.
Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009650680
INSPECTION AFTER REMOVAL
1.
Front suspension member
2.
Rebound stopper
3.
Front suspension member stay
: N·m (kg-m, ft-lb)
JPEIA0131GB
FSU-18
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
Check front suspension member for cracks, wear or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
BRC-119, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
(with VDC).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст