Nissan Quest E52. Instruction — part 572
EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-37
< REMOVAL AND INSTALLATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Prevent rust preventives from adhering to the sensor body.
Inspection
INFOID:0000000009652770
INSPECTION AFTER REMOVAL
Surface Distortion
• Check the surface distortion of the exhaust manifold mating sur-
face with a straightedge and a feeler gauge.
• If it exceeds the limit, replace exhaust manifold.
Limit
: Refer to
.
PBIC1173E
EM-38
< REMOVAL AND INSTALLATION >
[VQ35DE]
OIL PAN AND OIL STRAINER
OIL PAN AND OIL STRAINER
Exploded View
INFOID:0000000009652771
Removal and Installation
INFOID:0000000009652772
REMOVAL
CAUTION:
To avoid the danger of being scalded, never drain engine oil when the engine is hot.
NOTE:
When removing oil pan (lower) or oil strainer only, take step 1 then step 32 and 33.
1.
Drain engine oil. Refer to
.
CAUTION:
Never spill engine oil on drive belt.
1.
Oil pan (upper)
2.
O-ring
3.
Oil pan gasket (front)
4.
Relief valve
5.
Oil pressure switch
6.
Oil cooler
7.
Connector bolt
8.
Oil filter
9.
Oil strainer
10. Drain plug
11.
Drain plug washer
12. Oil pan (lower)
13. Rear plate cover
14. Crankshaft position sensor (POS)
15. Oil pan gasket (rear)
A.
Comply with the assembly procedure
when tightening. Refer to
B.
To oil pump
C.
Oil pan side
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Sealing point
JPBIA1636GB
OIL PAN AND OIL STRAINER
EM-39
< REMOVAL AND INSTALLATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Drain engine coolant. Refer to
CAUTION:
Never spill engine coolant on drive belt.
3.
Remove following parts:
• Front road wheel and tires (RH and LH).
• Splash guard (RH and LH): Refer to
• Exhaust front tube: Refer to
.
• Drive belt: Refer to
EM-13, "Removal and Installation"
• Engine under cover.
• Crankshaft position sensor.
4.
Remove A/C compressor with piping connected, and temporarily secure it to aside. Refer to
"COMPRESSOR : Removal and Installation"
.
5.
Remove oil level gauge. Refer to
6.
Remove air duct (inlet). Refer to
EM-26, "Removal and Installation"
.
7.
Remove extension cowl top. Refer to
EXT-22, "Removal and Installation"
8.
Remove high pressure side piping from intake manifold collector. Refer to
.
9.
Remove heater tube bracket (front). Refer to
.
10. Remove vacuum hose from engine mounting (front and rear). Refer to
.
11. Remove front drive shaft (RH). Refer to
FAX-19, "RIGHT SIDE : Removal and Installation"
.
12. Remove heat insulator. Refer to
.
13. Remove steering lower joint. Refer to
14. Remove three way catalyst (bank 1 and bank 2). Refer to
EM-33, "Removal and Installation"
15. Remove oil pressure switch.
16. Remove oil filter. Refer to
LU-11, "Removal and Installation"
17. Remove engine mounting insulator (front and rear) fixing nuts. Refer to
.
18. Remove front drive shaft (LH) from transaxle. Refer to
FAX-18, "LEFT SIDE : Removal and Installation"
19. Remove CVT fluid cooler hose from front suspension member.
20. Remove the connector of auto levelizer control unit and clip.
21. Remove the mounting nuts of stabilizer connecting rod upper side. Refer to
.
22. Remove power steering return hose and power steering return tube from front suspension member. Refer
23. Support transaxle assembly with a suitable jack.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
24. Remove engine mounting insulator (LH) mounting bolts from front suspension member. Refer to
25. Remove rear torque rod and rear torque rod bracket. Refer to
EM-56, "Removal and Installation"
26. Support front suspension member assembly with a suitable jack.
27. Remove member stay, front suspension member fixing bolts and bolts. Refer to
.
28. Lower the jack on the front suspension side to the height where the hose of power steering is not
stretched taut.
29. Remove support bearing bracket. Refer to
30. Remove oil cooler and water pipe. Refer to
31. Remove oil pan (lower) as follows:
EM-40
< REMOVAL AND INSTALLATION >
[VQ35DE]
OIL PAN AND OIL STRAINER
a.
Loosen mounting bolts in the reverse order as shown in the fig-
ure to remove.
b.
Insert the seal cutter [SST: KV10111100 (J-37228)] (A) between
oil pan (upper) and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surfaces.
• Never insert a screwdriver, this will damage the mating
surfaces.
c.
Slide the seal cutter by tapping on the side of tool with a ham-
mer. Remove oil pan (lower).
32. Remove oil strainer.
33. Loosen mounting bolts in the reverse order as shown in the fig-
ure to remove.
• Insert the seal cutter [SST: KV10111100 (J-37228)] between
oil pan (upper) and cylinder block. Slide seal cutter by tapping
on the side of tool with a hammer. Remove oil pan (upper).
CAUTION:
• Be careful not to damage the mating surfaces.
• Never insert a screwdriver, this will damage the mating
surfaces.
34. Remove O-rings (2) from bottom of cylinder block (1) and oil
pump (3).
PBIC0782E
JPBIA0276ZZ
PBIC1636E
: Engine front
JPBIA1379ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст