Nissan Quest E52. Instruction — part 1161
B1215, B1216, B1217 SATELLITE SENSOR LH
SRC-173
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> INSPECTION END
SRC-174
< DTC/CIRCUIT DIAGNOSIS >
B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT
B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009650009
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-174, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009650010
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1218
B1219
B1220
B1221
B1222
B1223
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT
SRC-175
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009650011
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-175, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009650012
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1234
B1235
B1236
B1237
B1238
B1239
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
SRC-176
< DTC/CIRCUIT DIAGNOSIS >
B1250, B1251, B1252, B1253, B1254, B1255 DIAGNOSIS SENSOR UNIT
B1250, B1251, B1252, B1253, B1254, B1255 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009650013
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-15, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-176, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009650014
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1250
B1251
B1252
B1253
B1254
B1255
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст