Nissan Quest E52. Instruction — part 310
DAS-82
< SYMPTOM DIAGNOSIS >
[BSW]
BSW SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
BSW SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009940773
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
NOTE:
For the operational conditions of BSW, refer to
Symptom
Possible cause
Inspection item/Reference page
Indicator/warning lamps do not il-
luminate when ignition switch
OFF
⇒
ON.
BSW warning lamp (Yellow)
does not illuminate
• BSW warning lamp signal
(CAN)
- Combination meter
- BSW control module
• BSW warning lamp (combina-
tion meter)
• Power supply and ground cir-
cuit of BSW control module
Refer to
TROL MODULE : Diagnosis
Procedure"
• BSW control module Active
test “BSW/BSI WARNING
LAMP”
Refer to
.
• BSW control module Data
monitor “BSW/BSI WARN
LMP”
Refer to
• Combination meter Data mon-
itor “BSW W/L”
Refer to
BSW ON indicator (on the
BSW switch) does not illumi-
nate
• Harness between BSW con-
trol module and BSW switch
• BSW switch
• BSW control module
BSW ON indicator circuit
Refer to
BSW indicator does not turn
ON
• Harness between side radar
and BSW indicator
• Side radar LH/RH
• BSW indicator
Perform self-diagnosis of side ra-
dar
Refer to
BSW system is not activated.
(Indicator/warning lamps illumi-
nate when ignition switch OFF
⇒
ON.)
BSW ON indicator is not
turned ON
⇔
OFF when op-
erating BSW switch
• Harness between BSW con-
trol module and BSW switch
• Harness between BSW
switch and ground
• BSW control module
• BSW switch
BSW ON indicator circuit
Refer to
Buzzer is not sounding
• BSW control module
• Combination meter
Meter buzzer circuit
Refer to
DAS
NORMAL OPERATING CONDITION
DAS-83
< SYMPTOM DIAGNOSIS >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
NORMAL OPERATING CONDITION
Description
INFOID:0000000009940774
PRECAUTIONS FOR BLIND SPOT WARNING (BSW)
• The BSW system is not a replacement for proper driving procedure and are not designed to prevent contact
with vehicles or objects. When changing lanes, always use the side and rear mirrors and turn and look in the
direction driver will move to ensure it is safe to change lanes. Never rely solely on the BSW system.
• The BSW system may not provide a warning for vehicles that pass through the detection zone quickly.
• Do not use the BSW system when towing a trailer because the system may not function properly.
• Excessive noise (e.g. audio system volume, open vehicle window) will interfere with the chime sound, and it
may not be heard.
• The side radar may not be able to detect and activate BSW when certain objects are present such as:
- Pedestrians, bicycles, animals.
- Several types of vehicles such as motorcycles.
- Oncoming vehicles.
- Vehicles remaining in the detection zone when driver accelerate from a stop.
- A vehicle merging into an adjacent lane at a speed approximately the same as vehicle.
- A vehicle approaching rapidly from behind.
- A vehicle which vehicle overtakes rapidly.
• Severe weather or road spray conditions may reduce the ability of the side radar to detect other vehicles.
• The side radar detection zone is designed based on a standard lane width. When driving in a wider lane, the
side radar may not detect vehicles in an adjacent lane. When driving in a narrow lane, the side radar may
detect vehicles driving two lanes away.
• The side radar are designed to ignore most stationary objects, however objects such as guardrails, walls,
foliage and parked vehicles may occasionally be detected. This is a normal operating condition.
DAS-84
< REMOVAL AND INSTALLATION >
[BSW]
BSW CONTROL MODULE
REMOVAL AND INSTALLATION
BSW CONTROL MODULE
Removal and Installation
INFOID:0000000009940775
REMOVAL
1.
Remove cluster lid C. Refer to
IP-14, "Removal and Installation"
2.
Remove mounting bolts from BSW control module.
3.
Disconnect BSW control module connector.
4.
Remove BSW control module.
INSTALLATION
Install in the reverse order of removal.
DAS
SIDE RADAR
DAS-85
< REMOVAL AND INSTALLATION >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
SIDE RADAR
Removal and Installation
INFOID:0000000009940776
EXPLODED VIEW
REMOVAL AND INSTALLATION
Removal
1.
Remove the rear bumper fascia assembly. Refer to
EXT-16, "REAR BUMPER : Removal and Installation"
.
2.
Remove the side radar connector.
NOTE:
This illustration is an example.
3.
Remove the mounting nuts to remove the side radar RH/LH from bracket.
Installation
Note the following, and install in the reverse order of removal.
1.
Bracket
2.
Side radar LH
3.
Bracket
4.
Bracket
5.
Side radar RH
6.
Bracket
A.
LH side
B.
RH side
Refer to
for symbol makes in the figure.
JSOIA0511GB
JSOIA0280ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст