Nissan Quest E52. Instruction — part 23
MIRROR SENSOR
ADP-85
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
NO
>> Refer to
ADP-85, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009649677
1.
CHECK DOOR MIRROR SENSOR (PASSENGER SIDE) POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-112, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
(+)
(-)
Voltage (V)
Door mirror (passenger side)
Connector
Terminals
D3
23
Ground
4 – 6
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M75
21
D3
23
Existed
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
21
Not existed
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M75
20
D3
24
Existed
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
20
Not existed
ADP-86
< DTC/CIRCUIT DIAGNOSIS >
MIRROR SENSOR
4.
CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR CIRCUIT
1.
Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.
2.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace door mirror sensor (built in passenger side door mirror).
NO
>> Repair or replace harness or connector.
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M75
5
D3
21
Existed
17
22
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
5
Not existed
17
SLIDING MOTOR
ADP-87
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SLIDING MOTOR
Component Function Check
INFOID:0000000009649678
1.
CHECK FUNCTION
1.
Select “SEAT SLIDE” in “Active test” mode with CONSULT.
2.
Check the sliding motor operation.
Is the operation of relevant parts normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009649679
1.
CHECK SLIDING MOTOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding motor connector.
3.
Turn ignition switch ON.
4.
Perform “Active test” (“SEAT SLIDE”) with CONSULT.
5.
Check voltage between sliding motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding motor (built in seat slide cushion frame).
NO
>> GO TO 2.
2.
CHECK SLIDING MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and sliding motor harness connector.
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
Test item
Description
SEAT SLIDE
OFF
Seat sliding
Stop
FR
Forward
RR
Backward
(+)
(-)
Condition
Voltage (V)
Sliding motor
Connector
Terminals
B561
34
Ground
SEAT SLIDE
OFF
0 – 1
Backward
9 – 16
38
OFF
0 – 1
Forward
9 – 16
Driver seat control unit
Sliding motor
Continuity
Connector
Terminal
Connector
Terminal
B551
34
B561
34
Existed
38
38
Driver seat control unit
Ground
Continuity
Connector
Terminal
B551
34
Not existed
38
ADP-88
< DTC/CIRCUIT DIAGNOSIS >
SLIDING MOTOR
YES
>> Replace driver seat control unit. Refer to
ADP-111, "Removal and Installation"
NO
>> Repair or replace harness or connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст