Nissan Quest E52. Instruction — part 1109
SEC-126
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
NO
>> GO TO 1.
DOOR KEY CYLINDER
DOOR KEY CYLINDER : Description
INFOID:0000000009650801
ARMED phase is not activated when all doors are locked using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• SECURITY ALARM SET: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR KEY CYLINDER : Diagnosis Procedure
INFOID:0000000009650802
1.
CHECK POWER DOOR LOCK SYSTEM
Lock or unlock doors using mechanical key.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system. Refer to
DLK-371, "Diagnosis Procedure"
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000009650803
Armed phase is not activated when all doors are locked by door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000009650804
1.
CHECK DOOR LOCK FUNCTION
Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
SEC-127
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
Description
INFOID:0000000009650805
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
Diagnosis Procedure
INFOID:0000000009650806
1.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-241, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the malfunctioning door switch
2.
CHECK HEADLAMPS FUNCTION
Check head lamps function.
Refer to
SEC-119, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK HORN FUNCTION
Check horn function.
Refer to
SEC-120, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
SEC-128
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
NATS ANTENNA AMP.
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Removal and Installation
INFOID:0000000009650807
REMOVAL
1.
Remove the push-button ignition switch. Refer to
SEC-129, "Removal and Installation"
.
2.
Press the NATS antenna amp. fixing pawls in the direction of the
arrow (1), as shown in the figure, to disengage them.
3.
Push NATS antenna amp. (1) in the direction of the arrow (2), as
shown in the figure, to remove it from instrument finisher A (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA8236ZZ
PUSH-BUTTON IGNITION SWITCH
SEC-129
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PUSH-BUTTON IGNITION SWITCH
Removal and Installation
INFOID:0000000009650808
REMOVAL
1.
Remove instrument finisher A. Refer to
IP-14, "Removal and Installation"
2.
Disconnect NATS antenna amp. connector and push-button ignition switch connector.
3.
Disengage the push-button ignition switch fixing pawls by push-
ing them in the direction of the arrow (1) as shown in the figure.
4.
Push push-button ignition switch (1) in the direction of the arrow
(2), as shown in the figure, and remove push-button ignition
switch from NATS antenna amp (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA8237ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст