Nissan Quest E52. Instruction — part 380
DLK-234
< DTC/CIRCUIT DIAGNOSIS >
B2627 OUTSIDE ANTENNA
B2627 OUTSIDE ANTENNA
DTC Logic
INFOID:0000000009649138
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
DLK-234, "Diagnosis Procedure"
.
NO
>> Outside key antenna (driver side) is OK.
Diagnosis Procedure
INFOID:0000000009649139
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch ON.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and front door outside handle assembly LH connector.
2.
Check continuity between BCM harness connector and front door outside handle assembly LH harness
connector.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2627
OUTSIDE ANTENNA
An excessive high or low voltage from front door left
outside key antenna is sent to BCM
• Front door left outside key antenna
• Harness or connector
(Front door left outside key anten-
na circuit is open or shorted)
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M124
78,79
Ground
When the driver door
request switch is oper-
ated with power
switch ON
When Intelligent Key
is in the antenna de-
tection area (The dis-
tance between
Intelligent Key and an-
tenna: 80 cm or less)
When Intelligent Key
is not in the antenna
detection area (The
distance between In-
telligent Key and an-
tenna: Approx. 2 m)
JMKIA5955GB
JMKIA5954GB
B2627 OUTSIDE ANTENNA
DLK-235
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace outside key antenna (driver side). (New antenna or other antenna)
2.
Connect BCM connector and front door outside handle assembly LH connector.
3.
Turn ignition switch ON.
4.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace front door outside handle assembly LH (outside key antenna).
NO
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
BCM
Front door outside handle assembly LH
Continuity
Connector
Terminal
Connector
Terminal
M124
78
D32
1
Existed
79
2
BCM
Ground
Continuity
Connector
Terminal
M124
78
Not existed
79
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M124
78,79
Ground
When the driver door
request switch is oper-
ated with power
switch ON
When Intelligent Key
is in the antenna de-
tection area (The dis-
tance between
Intelligent Key and an-
tenna: 80 cm or less)
When Intelligent Key
is not in the antenna
detection area (The
distance between In-
telligent Key and an-
tenna: Approx. 2 m)
JMKIA5955GB
JMKIA5954GB
DLK-236
< DTC/CIRCUIT DIAGNOSIS >
B2628 OUTSIDE ANTENNA
B2628 OUTSIDE ANTENNA
DTC Logic
INFOID:0000000009649140
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
DLK-230, "Diagnosis Procedure"
.
NO
>> Outside key antenna (rear bumper) is OK.
Diagnosis Procedure
INFOID:0000000009649141
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch ON.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and outside key antenna (rear bumper) connector.
2.
Check continuity between BCM harness connector and outside key antenna (rear bumper) harness con-
nector.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2628
OUTSIDE ANTENNA
An excessive high or low voltage from outside key
antenna (rear bumper) is sent to BCM
• Outside key antenna (rear
bumper)
• Harness or connector
(Outside key antenna (rear
bumper) circuit is open or shorted)
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M124
82, 83
Ground
When the back door
request switch is oper-
ated with power
switch ON
When Intelligent Key
is in the antenna de-
tection area (The dis-
tance between
Intelligent Key and an-
tenna: 80 cm or less)
When Intelligent Key
is not in the antenna
detection area (The
distance between In-
telligent Key and an-
tenna: Approx. 2 m)
JMKIA5955GB
JMKIA5954GB
B2628 OUTSIDE ANTENNA
DLK-237
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace outside key antenna (rear bumper). (New antenna or other antenna)
2.
Connect BCM and outside key antenna (rear bumper) connector.
3.
Turn ignition switch ON.
4.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace outside key antenna (rear bumper).
NO
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
BCM
Outside key antenna (rear bumper)
Continuity
Connector
Terminal
Connector
Terminal
M124
82
B303
1
Existed
83
2
BCM
Ground
Continuity
Connector
Terminal
M124
82
Not existed
83
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M124
82, 83
Ground
When the back door
request switch is oper-
ated with power
switch ON
When Intelligent Key
is in the antenna de-
tection area (The dis-
tance between
Intelligent Key and an-
tenna: 80 cm or less)
When Intelligent Key
is not in the antenna
detection area (The
distance between In-
telligent Key and an-
tenna: Approx. 2 m)
JMKIA5955GB
JMKIA5954GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст