Nissan Quest E52. Instruction — part 514
EC-266
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0300, P0301, P0302, P0303, P0304, P0305, P0306 MISFIRE
3.
Crank engine for approximately 3 seconds, and recheck whether spark is generated between the spark
plug and the grounded metal portion.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Check ignition coil, power transistor and their circuits. Refer to
.
7.
CHECK SPARK PLUG
Check the initial spark plug for fouling, etc.
Is the inspection result normal?
YES
>> Replace spark plug(s) with standard type one(s). For
spark plug type, refer to
.
NO
>> Repair or clean spark plug. Then GO TO 8.
8.
CHECK FUNCTION OF IGNITION COIL-III
1.
Reconnect the initial spark plugs.
2.
Crank engine for approximately 3 seconds, and recheck whether spark is generated between the spark
plug and the grounded portion.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace spark plug(s) with standard type one(s). For spark plug type, refer to
9.
CHECK COMPRESSION PRESSURE
Check compression pressure. Refer to
.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Check pistons, piston rings, valves, valve seats and cylinder head gaskets.
10.
CHECK FUEL PRESSURE
1.
Install all removed parts.
2.
Release fuel pressure to zero. Refer to
.
3.
Install fuel pressure gauge kit [SST: — (J-44321)] and check fuel pressure. Refer to
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> GO TO 11.
11.
DETECT MALFUNCTIONING PART
Check fuel hoses and fuel tubes for clogging.
Is the inspection result normal?
YES
>> Replace “fuel filter and fuel pump assembly”. Refer to
.
NO
>> Repair or replace malfunctioning part.
12.
CHECK IGNITION TIMING
Check idle speed and ignition timing.
Spark should be generated.
SEF156I
Spark should be generated.
At idle: Approximately 350 kPa (3.57 kg/cm
2
, 51 psi)
P0300, P0301, P0302, P0303, P0304, P0305, P0306 MISFIRE
EC-267
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
For procedure, refer to
.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Follow the
.
13.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect corresponding A/F sensor 1 harness connector.
3.
Disconnect ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
5.
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
6.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
14.
CHECK A/F SENSOR 1 HEATER
Check A/F sensor 1 heater. Refer to
EC-173, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 15.
NO
>> Replace malfunctioning A/F sensor 1. Refer to
.
15.
CHECK MASS AIR FLOW SENSOR
With CONSULT
1.
Check “MASS AIR FLOW” in “DATA MONITOR” mode with CONSULT.
2.
For specification, refer to
EC-461, "Mass Air Flow Sensor"
With GST
1.
Check mass air flow sensor signal in Service $01 with GST.
2.
For specification, refer to
EC-461, "Mass Air Flow Sensor"
A/F sensor 1
ECM
Continuity
Bank
Connector
Terminal
Connector
Terminal
1
F27
1
F8
69
Existed
2
73
2
F64
1
77
2
81
A/F sensor 1
Ground
Continuity
Bank
Connector
Terminal
1
F27
1
Ground
Not existed
2
2
F64
1
2
ECM
Ground
Continuity
Connector
Terminal
F8
69
Ground
Not existed
73
77
81
EC-268
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0300, P0301, P0302, P0303, P0304, P0305, P0306 MISFIRE
Is the measurement value within the specification?
YES
>> GO TO 16.
NO
>> Check connectors for rusted terminals or loose connections in the mass air flow sensor circuit or
ground. Refer to
16.
CHECK SYMPTOM TABLE
Check items on the rough idle symptom in
.
Is the inspection result normal?
YES
>> GO TO 17.
NO
>> Repair or replace malfunctioning part.
17.
ERASE THE 1ST TRIP DTC
Some tests may cause a 1st trip DTC to be set.
Erase the 1st trip DTC from the ECM memory after performing the tests. Refer to
.
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
P0327, P0328, P0332, P0333 KS
EC-269
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0327, P0328, P0332, P0333 KS
DTC Logic
INFOID:0000000009651110
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and run it for at least 5 seconds at idle speed.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009651111
1.
CHECK KNOCK SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Disconnect knock sensor harness connector and ECM harness connector.
2.
Check the continuity between knock sensor harness connector and ECM harness connector.
3.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
2.
CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between knock sensor harness connector and ECM harness connector.
DTC No.
Trouble diagnosis
name
DTC detected condition
Possible cause
P0327
Knock sensor (bank 1)
circuit low input
An excessively low voltage from the sensor is
sent to ECM.
• Harness or connectors
(The sensor circuit is open or shorted.)
• Knock sensor
P0328
Knock sensor (bank 1)
circuit high input
An excessively high voltage from the sensor is
sent to ECM.
P0332
Knock sensor (bank 2)
circuit low input
An excessively low voltage from the sensor is
sent to ECM.
P0333
Knock sensor (bank 2)
circuit high input
An excessively high voltage from the sensor is
sent to ECM.
DTC
Knock sensor
ECM
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0327, P0328
1
F201
2
F8
91
Existed
P0332, P0333
2
F202
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст