Nissan Quest E52. Instruction — part 330
DLK-34
< SYSTEM DESCRIPTION >
SYSTEM (POWER DOOR LOCK SYSTEM)
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more.
P Range Interlock Door Lock
All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion, all doors are closed and the shift signal received from the TCM via CAN communication shifted from the
P position to any position other than P.
Setting change of Automatic Door Lock/Unlock Function
The lock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT
The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT.
Without CONSULT
The automatic door lock function ON/OFF can be switched by performing the following operation.
1.
Close all doors (door switch OFF)
2.
Ignition switch: OFF
→
ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.
4.
The switching complete when the hazard lamp blinks.
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)
The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 2 types as per the following items.
IGN OFF Interlock Door Unlock
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
P Range Interlock Door Unlock
All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.
Setting change of Automatic Door Lock/Unlock Function
The unlock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT
The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT.
Without CONSULT
The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.
1.
Close all doors (door switch OFF)
2.
Ignition switch: OFF
→
ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.
4.
The switching is complete when the hazard lamp blinks.
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
SYSTEM (POWER DOOR LOCK SYSTEM)
DLK-35
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Circuit Diagram
INFOID:0000000009648975
JMKIA8112GB
DLK-36
< SYSTEM DESCRIPTION >
SYSTEM (INTELLIGENT KEY SYSTEM)
SYSTEM (INTELLIGENT KEY SYSTEM)
INTELLIGENT KEY SYSTEM
INTELLIGENT KEY SYSTEM : System Description
INFOID:0000000009648976
SYSTEM DIAGRAM
*1
:With back door auto closure system
*2
:With automatic back door system
*
:With automatic sliding door system
• The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/
unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verifica-
tion using two-way communication between the Intelligent Key and the vehicle (BCM).
NOTE:
The driver should always carry the Intelligent Key
• The settings for each function can be changed with CONSULT.
• If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can be
registered.
• It is possible to perform a diagnosis on the system and register an Intelligent Key with CONSULT.
JMKIA8008GB
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-37
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Function
Description
Refer
Door lock
Lock/unlock can be performed by pressing the request switch
Back door opener
The back door can be opened by carrying the Intelligent Key and pressing the
back door opener switch
Remote keyless entry
Lock/unlock can be performed by pressing the remote controller button of the In-
telligent Key
Key reminder
The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle
Warning
If an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver
Engine start
The engine can be turned on while carrying the Intelligent Key
Interior room lamp control
Interior room lamp is controlled according to door lock/unlock state
Power window
Power window can be operated by Intelligent Key button operation
Automatic drive positioner
Automatic drive positioner system can be operated by door unlock operation
Panic alarm
When Intelligent Key panic alarm button is pressed, horn sounds
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст