Nissan Quest E52. Instruction — part 497
EC-198
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0122, P0123 TP SENSOR
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK THROTTLE POSITION SENSOR 2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.
CHECK THROTTLE POSITION SENSOR
Check throttle position sensor. Refer to
EC-198, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Replace electric throttle control actuator. Refer to
Component Inspection
INFOID:0000000009651056
1.
CHECK THROTTLE POSITION SENSOR
1.
Turn ignition switch OFF.
2.
Reconnect all harness connectors disconnected.
3.
.
4.
Turn ignition switch ON.
5.
Set selector lever to D position.
6.
Check the voltage between ECM harness connector terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace electric throttle control actuator. Refer to
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
4
F7
19
Existed
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
3
F7
23
Existed
ECM
Condition
Voltage
Connector
+
–
Terminal
Terminal
F7
22
(TP sensor 1 sig-
nal)
19
(Sensor ground)
Accelerator pedal
Fully released
More than 0.36 V
Fully depressed
Less than 4.75 V
23
(TP sensor 2 sig-
nal)
Fully released
Less than 4.75 V
Fully depressed
More than 0.36 V
P0125 ECT SENSOR
EC-199
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0125 ECT SENSOR
DTC Logic
INFOID:0000000009651057
DTC DETECTION LOGIC
NOTE:
• If DTC P0125 is displayed with P0116, first perform the trouble diagnosis for DTC P0116. Refer to
.
• If DTC P0125 is displayed with P0117 or P0118, first perform the trouble diagnosis for DTC P0117,
P0118. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
CHECK ENGINE COOLANT TEMPERATURE SENSOR FUNCTION
With CONSULT
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT.
3.
Check that “COOLAN TEMP/S” is above 10
°
C (50
°
F).
With GST
Follow the procedure “With CONSULT” above.
Is the temperature above 10
°
C (50
°
F)?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Start engine and run it for 65 minutes at idle speed.
If “COOLAN TEMP/S” increases to more than 10
°
C (50
°
F) within 65 minutes, stop engine because
the test result will be OK.
CAUTION:
Never overheat engine.
2.
Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
YES
>>
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009651058
1.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
Check engine coolant temperature sensor. Refer to
EC-200, "Component Inspection"
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0125
Insufficient engine cool-
ant temperature for
closed loop fuel control
• Voltage sent to ECM from the sensor is not
practical, even when some time has passed
after starting the engine.
• Engine coolant temperature is insufficient for
closed loop fuel control.
• Harness or connectors
(High resistance in the circuit)
• Engine coolant temperature sensor
• Thermostat
EC-200
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0125 ECT SENSOR
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace engine coolant temperature sensor.
2.
CHECK THERMOSTAT OPERATION
When the engine is cold [lower than 70
°
C (158
°
F)] condition, grasp lower radiator hose and confirm that the
engine coolant does not flow.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Repair or replace thermostat. Refer to
.
Component Inspection
INFOID:0000000009651059
1.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect engine coolant temperature sensor harness connector.
3.
Remove engine coolant temperature sensor. Refer to
.
4.
Check resistance between engine coolant temperature sensor
terminals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace engine coolant temperature sensor. Refer to
Terminals
Condition
Resistance (k
Ω
)
1 and 2
Temperature [
°
C (
°
F)]
20 (68)
2.1 - 2.9
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
JMBIA0080ZZ
P0127 IAT SENSOR
EC-201
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0127 IAT SENSOR
DTC Logic
INFOID:0000000009651060
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
This test may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road
test is expected to be easier, it is unnecessary to lift the vehicle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Wait until engine coolant temperature is less than 96
°
C (205
°
F)
-
Turn ignition switch ON.
-
Select “DATA MONITOR” mode with CONSULT.
-
Check the engine coolant temperature.
-
If the engine coolant temperature is not less than 96
°
C (205
°
F), turn ignition switch OFF and cool down
engine.
NOTE:
Perform the following steps before engine coolant temperature is above 96
°
C (205
°
F).
2.
Turn ignition switch ON.
3.
Select “DATA MONITOR” mode with CONSULT.
4.
Start engine.
5.
Hold vehicle speed at more than 70 km/h (43 MPH) for 100 consecutive seconds.
CAUTION:
Always drive vehicle at a safe speed.
6.
Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009651061
1.
CHECK INTAKE AIR TEMPERATURE SENSOR
Check intake air temperature sensor. Refer to
EC-202, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Replace mass air flow sensor (with intake air temperature sensor).
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0127
Intake air temperature
too high
Rationally incorrect voltage from the sensor is
sent to ECM, compared with the voltage signal
from engine coolant temperature sensor.
• Harness or connectors
(The sensor circuit is open or shorted)
• Intake air temperature sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст