Nissan Pathfinder (2011 year). Instruction — part 434
GW-18
< UNIT REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
3. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten glass bolts.
4. Check the glass for proper fit.
5. On the drivers door, reset the motor. Follow the "Setting of Limit Switch" procedure.
6. Reposition the vapor barrier.
7. Install front door finisher. Refer to
INT-15, "Removal and Installation"
.
SETTING AFTER INSTALLATION
Setting of Limit Switch
If any of the following work has been done, set the limit switch (integrated in the motor).
• Battery cable is disconnected.
• Power window switch connector disconnected.
• Removal and installation of the regulator.
• Removal and installation of the motor from the regulator.
• Removal and installation of the glass.
• Removal and installation of the glass run.
• Window is partly opened and/or closed many times without being fully closed.
Resetting
After installing each component, perform the following procedure to reset the limit switch.
1. Raise the glass to the top position.
2. While pressing and holding the reset switch, lower the glass to
the bottom position.
3. Release the reset switch. Verify that the reset switch returns to
the original position, if not, pull the switch using suitable tool.
4. Raise the glass to the top position.
CAUTION:
Do not operate the glass automatically to raise the glass to
the top position.
Glass mounting bolts : 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1686E
SIIA0347E
2011 Pathfinder
REAR DOOR GLASS AND REGULATOR
GW-19
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS AND REGULATOR
Rear Door Glass
INFOID:0000000006247198
REMOVAL
1. Remove the rear door finisher. Refer to
INT-15, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
4. Remove the glass run from the partition glass.
5. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
6. Remove the partition sash bolt (lower) and screw (upper) to
remove the sash.
7. Remove the bolts and the glass.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass alignment. Refer to "FITTING INSPECTION".
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass carrier plate bolts to correct the glass position.
Rear Door Glass Regulator
INFOID:0000000006247199
REMOVAL
1. Remove the rear door finisher. Refer to
INT-15, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
4. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
LIIA1689E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1689E
2011 Pathfinder
GW-20
< UNIT REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
5. Raise the rear door glass and hold it in place with suitable tool
(A).
6. Remove the bolts and the regulator assembly.
• Disconnect the connector from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Gear wear
• Regulator deformation
• Spring damage
• Grease condition for each sliding part
INSTALLATION
1. Connect the harness connector and install the regulator assembly.
PIIB3511J
Front
WIIA1034E
2011 Pathfinder
REAR DOOR GLASS AND REGULATOR
GW-21
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b. Install the top front regulator bolt.
c. Install the bottom regulator bolt.
d. Tighten the top rear regulator bolt.
e. Install the top window motor bolt.
f.
Install the lower window motor bolt.
g. Install the front window motor bolt.
2. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten the bolts.
3. Install the partition sash
4. Check the glass alignment.
5. Reposition the vapor barrier.
6. Install the rear door finisher. Refer to
INT-15, "Removal and Installation"
Front
Regulator assembly
: 7.5 N·m (0.77 kg-m, 66 in-lb)
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
WIIA1034E
LIIA1689E
2011 Pathfinder
GW-22
< UNIT REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
SIDE WINDOW GLASS
Removal and Installation
INFOID:0000000006247200
1.
Glass
2.
Primer area
3.
Body side outer
4.
Rear door assembly
5.
Back door assembly
6.
Locating clips
7.
Urethane
a.
15 mm (0.59 in)
b.
42.5 mm (1.67 in)
WIIA1035E
2011 Pathfinder
SIDE WINDOW GLASS
GW-23
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REMOVAL
1. Remove the luggage side lower and upper finisher. Refer to
INT-25, "Removal and Installation"
2. Disconnect the antenna.
3. If the window glass is to be reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
4. Remove the glass using piano wire or power cutting tool and an inflatable pump bag.
CAUTION:
• When the side window glass is to be reused, do not use a cutting knife or power cutting tool.
• Be careful not to scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
Installation is in the reverse order of removal.
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• Check gap along bottom to confirm that glass does not contact sheet metal.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the glass in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperatures and lower humidities.
Repairing Water Leaks for Side Window Glass
Leaks can be repaired without removing or reinstalling glass.
If water is leaking between urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the side window area while pushing glass outward.
To stop leak, apply primer (if necessary) and then urethane adhesive to the leak point.
c.
3.0 mm (0.12 in)
d.
2.5 mm (0.1 in)
e.
12 mm (0.47 in)
f.
7.0 mm (0.28 in)
g.
11.5 mm (0.45 in)
h.
3.3 mm (0.13 in)
j.
30 mm (1.2 in)
2011 Pathfinder
GW-24
< UNIT REMOVAL AND INSTALLATION >
GLASS HATCH
GLASS HATCH
Removal and Installation
INFOID:0000000006247201
Removal
1. Remove the rear wiper motor assembly. Refer to
WW-75, "Removal and Installation"
.
2. Disconnect the rear defroster electrical connectors.
3. Remove the back door top garnish assembly. Refer to
INT-27, "Removal and Installation"
.
4. Remove the glass hatch stays.
5. Remove the glass hatch assembly.
CAUTION:
1.
Glass hatch hinge RH/LH
2.
Glass hatch stud
3.
Gas stay ball stud RH/LH
4.
Bushing
5.
Glass hatch striker
6.
Wiper motor bracket
7.
Wiper motor stud
8.
Harness protector
9.
Glass hatch
10. Glass hatch handle assembly
WIIA0743E
2011 Pathfinder
GLASS HATCH
GW-25
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
• Be careful not to scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
Installation
Installation is in the reverse order of removal.
Rear Window Stay Disposal
INFOID:0000000006247202
1. Fix window stay (1) using a vise (C).
2. Using hacksaw (A) slowly make two holes in the window stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on window stay, always cover a hack-
saw using a shop cloth (B) to avoid scattering metal frag-
ments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA3336ZZ
A: 20 mm (0.787 in)
B: Cut in numerical order as
shown at the groove.
JMKIA3609ZZ
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст