Nissan Pathfinder (2011 year). Instruction — part 77
AV
STEERING SWITCH
AV-435
< REMOVAL AND INSTALLATION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH
Removal and Installation
INFOID:0000000006246816
REMOVAL
1. Remove the driver air bag module. Refer to
SR-5, "Removal and Installation"
2. Remove the steering wheel audio control switch assembly screws.
3. Disconnect the steering wheel audio control switches connector.
4. Remove the steering wheel audio control switches by pulling on
steering wheel audio control switches to release the pawls.
•
: Pawl
CAUTION:
Do not tilt steering wheel audio control switches during
removal or damage may occur to the pawls.
INSTALLATION
Installation is in the reverse order of removal.
1. Steering wheel
2.
Steering wheel audio control switches
ALNIA0357ZZ
ALNIA1214ZZ
2011 Pathfinder
AV-436
< REMOVAL AND INSTALLATION >
[BOSE AUDIO WITH NAVIGATION]
MICROPHONE
MICROPHONE
Removal and Installation
INFOID:0000000006246817
REMOVAL
1. Remove the front roof console finisher. Refer to
INT-22, "Removal and Installation"
.
2. Detach the microphone (1) from the front console finisher tabs
(A).
3. Disconnect the microphone connector (B) and remove the
microphone (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0379ZZ
2011 Pathfinder
AV
REAR VIEW CAMERA
AV-437
< REMOVAL AND INSTALLATION >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REAR VIEW CAMERA
Removal and Installation
INFOID:0000000006246818
REMOVAL
1. Remove the license lamp finisher. Refer to
EXT-23, "Removal and Installation"
.
2. Disconnect the rear view camera connector.
3. Detach the rear view camera harness clip.
4. Detach the rear view camera to release, then pull out to remove the rear view camera while feeding the
rear view camera harness and connector through the back door.
INSTALLATION
Installation is in the reverse order of removal.
1.
Rear view camera
A.
Rear view camera connector
B.
Rear view camera harness clip
ALNIA1182ZZ
2011 Pathfinder
BCS
BCS-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
BCS
A
O
P
N
CONTENTS
BODY CONTROL SYSTEM
BASIC INSPECTION . . . . . . . . .
INSPECTION AND ADJUSTMENT . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . ...
CONFIGURATION . . . . . . . . . . . . . ...
CONFIGURATION : Description . . . . . . . ...
CONFIGURATION : Special Repair Requirement . ..
SYSTEM DESCRIPTION . . . . . . . ..
BODY CONTROL SYSTEM . . . . . . . .
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
COMBINATION SWITCH READING SYSTEM
. .
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ..
SIGNAL BUFFER SYSTEM . . . . . . . ...
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
POWER CONSUMPTION CONTROL SYS-
TEM . . . . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
DOOR LOCK . . . . . . . . . . . . . . . ..
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) . . . . . . . . . . . . . . ..
REAR DEFOGGER . . . . . . . . . . . . .
REAR DEFOGGER : CONSULT-III Function
(BCM - REAR DEFOGGER) . . . . . . . . ...
BUZZER . . . . . . . . . . . . . . . . . .
BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) . . . . . . . . . . . . . . . . . . ..
INT LAMP . . . . . . . . . . . . . . . . ...
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . ..
MULTI REMOTE ENT . . . . . . . . . . . .
MULTI REMOTE ENT : CONSULT-III Function
(BCM - MULTI REMOTE ENT) . . . . . . . .
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) . . . . . . . . . . . . . . ...
WIPER . . . . . . . . . . . . . . . . . .
WIPER : CONSULT-III Function (BCM - WIPER) .
FLASHER . . . . . . . . . . . . . . . . ...
FLASHER : CONSULT-III Function (BCM -
FLASHER) . . . . . . . . . . . . . . . ...
AIR CONDITIONER . . . . . . . . . . . . ...
AIR CONDITIONER : CONSULT-III Function
(BCM - AIR CONDITIONER) . . . . . . . . ...
INTELLIGENT KEY . . . . . . . . . . . . .
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) . . . . . . . . .
COMB SW . . . . . . . . . . . . . . . . ..
COMB SW : CONSULT-III Function (BCM -
COMB SW) . . . . . . . . . . . . . . . ..
BCM . . . . . . . . . . . . . . . . . . ...
2011 Pathfinder
BCS-2
BCM : CONSULT-III Function (BCM - BCM) . . ..
IMMU . . . . . . . . . . . . . . . . . . .
IMMU : CONSULT-III Function (BCM - IMMU) . ...
BATTERY SAVER . . . . . . . . . . . . ....
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) . . . . . . . . . . . ..
TRUNK . . . . . . . . . . . . . . . . . ..
TRUNK : CONSULT-III Function (BCM - TRUNK) ...
THEFT ALM . . . . . . . . . . . . . . . ..
THEFT ALM : CONSULT-III Function (BCM -
THEFT ALM) . . . . . . . . . . . . . . ..
RETAINED PWR . . . . . . . . . . . . . ...
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) . . . . . . . . . . . . ...
SIGNAL BUFFER . . . . . . . . . . . . . ..
SIGNAL BUFFER : CONSULT-III Function (BCM
- SIGNAL BUFFER) . . . . . . . . . . . ....
AIR PRESSURE MONITOR . . . . . . . . . ..
AIR PRESSURE MONITOR : CONSULT-III Func-
tion (BCM - AIR PRESSURE MONITOR) . . . ...
PANIC ALARM . . . . . . . . . . . . . . ..
PANIC ALARM : CONSULT-III Function (BCM -
PANIC ALARM) . . . . . . . . . . . . . ..
DTC/CIRCUIT DIAGNOSIS . . . . . . .
U1000 CAN COMM CIRCUIT . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ..
COMBINATION SWITCH INPUT CIRCUIT . ...
Diagnosis Procedure . . . . . . . . . . . ..
Special Repair Requirement . . . . . . . . ...
COMBINATION SWITCH OUTPUT CIRCUIT ...
Diagnosis Procedure . . . . . . . . . . . ...
Special Repair Requirement . . . . . . . . ...
COMBINATION SWITCH . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . .
BCM (BODY CONTROL MODULE) . . . . ..
Reference Value . . . . . . . . . . . . . .
Terminal Layout . . . . . . . . . . . . . ..
Physical Values . . . . . . . . . . . . . ...
Fail Safe . . . . . . . . . . . . . . . . .
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . .
BCM (BODY CONTROL MODULE) . . . . ..
Wiring Diagram . . . . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . .
COMBINATION SWITCH SYSTEM SYMP-
TOMS . . . . . . . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . . .
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ..
BCM (BODY CONTROL MODULE) . . . . ..
Removal and Installation . . . . . . . . . . .
2011 Pathfinder
BCS
INSPECTION AND ADJUSTMENT
BCS-3
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000006247430
When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before
replacement.
Configuration has three functions as follows
• READ CONFIGURATION is the function to read (extract) vehicle configuration of current BCM.
• WRITE CONFIGURATION - Instruction selection is the function to select and write vehicle configuration on
BCM instructionly.
• WRITE CONFIGURATION - Config file is the function to write vehicle configuration with the data extracted
from current BCM.
CAUTION:
• When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
• Complete the procedure of WRITE CONFIGURATION in order.
• If you set incorrect WRITE CONFIGURATION, incidents will occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000006247431
1.
SAVING VEHICLE SPECIFICATION
Perform “READ CONFIGURATION” with CONSULT-III to save or print current vehicle specification.
>> GO TO 2
2.
REPLACE BCM
BCS-55, "Removal and Installation"
.
>> GO TO 3
3.
WRITING VEHICLE SPECIFICATION
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Instruction selection” with
CONSULT-III to write vehicle specification. Refer to
BCS-3, "ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement"
>> GO TO 4
4.
INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
>> Work End.
CONFIGURATION
CONFIGURATION : Description
INFOID:0000000006247432
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM.
Configuration has three functions as follows
• READ CONFIGURATION is the function to read (extract) vehicle configuration of current BCM.
• WRITE CONFIGURATION - Instruction selection is the function to select and write vehicle configuration on
BCM instructionly.
• WRITE CONFIGURATION - Config file is the function to write vehicle configuration with the data extracted
from current BCM.
CAUTION:
2011 Pathfinder
BCS-4
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
• When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
• Complete the procedure of WRITE CONFIGURATION in order.
• If you set incorrect WRITE CONFIGURATION, incidents will occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
CONFIGURATION : Special Repair Requirement
INFOID:0000000006247433
1.
WRITING VEHICLE SPECIFICATION
Perform “WRITE CONFIGURATION” with CONSULT-III.
When writing saved data>>GO TO 2
When writing instructionly>>GO TO 3
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
Perform “WRITE CONFIGURATION - Config file” with CONSULT-III.
>> Work End.
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
For “WRITE CONFIGURATION - Instruction selection”, using the following flow chart, identify the correct model
and configuration list.
Confirm and/or change setting value for each item according to the configuration list.
Depending on CONSULT-III software version being used, some or all of the write configuration items shown in
the following configuration lists may be displayed. If an item does not display on the CONSULT-III “WRITE
CONFIGURATION - Instruction selection” screen, then it is an auto setting item and it cannot be instructionly set or
changed.
NOTE:
Confirm vehicle model. Refer to
>> Work End.
MANUAL SETTING ITEM
Items
Setting value
KEYLESS ENTRY
WITH
⇔
WITHOUT
I-KEY
WITH
⇔
WITHOUT
AUTO LIGHT
WITH
⇔
WITHOUT
DTRL
WITH
⇔
WITHOUT
THEFT ALARM
WITH
⇔
WITHOUT
ASSIST LAMP TYPE
MODE1
⇔
MODE2
AUTO DOOR UNLOCK TIMING
WITH I-KEY
⇔
WITHOUT I-KEY
2011 Pathfinder
BCS
BODY CONTROL SYSTEM
BCS-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYSTEM DESCRIPTION
BODY CONTROL SYSTEM
System Description
INFOID:0000000006247434
OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power consump-
tion control function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings.
BCM control function list
System
Refer to
Combination switch reading system
Signal buffer system
Power consumption control system
Auto light system
Turn signal and hazard warning lamp system
Headlamp system
Front fog lamp system (if equipped)
Daytime running light system (if equipped)
Interior room lamp control system
Step lamp system
Interior room lamp battery saver system
Front wiper and washer system
Rear wiper and washer system
Warning chime system
WCS-4, "WARNING CHIME SYSTEM : System Diagram"
Door lock system
• WITH INTELLIGENT KEY SYSTEM:
• WITHOUT INTELLIGENT KEY SYSTEM:
UNLOCK SWITCH : System Diagram"
(NATS) Nissan anti-theft system
• WITH INTELLIGENT KEY SYSTEM:
• WITHOUT INTELLIGENT KEY SYSTEM:
Vehicle security system
• WITH INTELLIGENT KEY SYSTEM:
• WITHOUT INTELLIGENT KEY SYSTEM:
Rear window defogger system
Remote keyless entry system
DLK-216, "REMOTE KEYLESS ENTRY : System Diagram"
Intelligent Key system (if equipped)
DLK-43, "CONSULT-III Function (INTELLIGENT KEY)"
Power window system
RAP (retained accessory power) system
BCS-26, "RETAINED PWR : CONSULT-III Function (BCM - RETAINED
PWR)"
TPMS (tire pressure monitoring system)
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст