Nissan Pathfinder (2011 year). Instruction — part 412
EXL-142
< REMOVAL AND INSTALLATION >
ADJUSTMENT AND INSPECTION
REMOVAL AND INSTALLATION
ADJUSTMENT AND INSPECTION
HEADLAMP
HEADLAMP : Aiming Adjustment
INFOID:0000000006247706
NOTE:
• For headlamp aiming details, refer to the regulations in your area.
• If vehicle front body has been repaired and/or the front combination lamp has been replaced, check head-
lamp aiming.
• Before performing aiming adjustment, check the following:
- Confirm headlamp aiming switch is set to "0" (zero) position.
- Ensure all tires are inflated to correct pressure.
- Place vehicle and screen on level surface.
- Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant and engine oil filled to correct level, and fuel tank full.
- Confirm spare tire, jack and tools are properly stowed.
- Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
- Use adjusting screw to perform aiming adjustment
LOW BEAM AND HIGH BEAM
A. Headlamp RH adjustment screw
B. Headlamp LH adjustment screw
AWKIA1436GB
2011 Pathfinder
ADJUSTMENT AND INSPECTION
EXL-143
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Aiming Chart
NOTE:
• By regulation, no means for horizontal aim adjustment is provided from the factory; only vertical aim is
adjustable.
• Basic illuminating area for evaluation and/or adjustment should be within range shown on aiming chart.
1. Use adjustment screw to perform aiming adjustment.
•
Cover the opposite lamp and ensure fog lamps, if equipped, are turned off.
CAUTION:
Do not tighten adjustment screw beyond specified torque or damage may occur.
2. Adjust beam pattern until cut-off line (top edge of illumination area) is positioned at the specified height off
ground. Measure cut-off line within distance J on H-line. See aiming chart.
FRONT FOG LAMP
FRONT FOG LAMP : Aiming Adjustment
INFOID:0000000006247707
The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing aiming
adjustment, make sure of the following.
• Keep all tires inflated to correct pressure.
WKIA4885E
1
Adjustment screen
2
Headlamp bulb center (HV point)
A
Minimum acceptable vertical aim di-
mension (see aiming chart)
B
Maximum acceptable vertical aim
dimension (see aiming chart)
C
H-V point
D
Distance of headlamp aiming screen
from vehicle 7.62 m (25 ft.)
E
Maximum aim evaluation distance
from vertical center on aiming
screen 399mm (3
°
R).
F
Minimum aim evaluation distance
from vertical center on aiming
screen 133 mm (1
°
R)
G
Aim evaluation area
H
Horizontal aiming evaluation line.
Right
A (Minimum acceptable vertical aim dimension)
-3.3 mm (0.13 in)
0.025
°
up
B (Maximum acceptable vertical aim dimension) 36.6 mm (1.44 in)
0.275
°
down
Adjustment torque
1.67 N.m (17 kg-cm, 14.8 in-lb)
2011 Pathfinder
EXL-144
< REMOVAL AND INSTALLATION >
ADJUSTMENT AND INSPECTION
• Place vehicle on level ground.
• See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and
tools). Have the driver or equivalent weight placed in driver seat.
Adjust aiming in the vertical direction by turning the adjustment
screw.
NOTE:
Use a Phillips screwdriver to adjust. Turn screw clockwise to raise
pattern and counterclockwise to lower pattern.
1. Set the distance between the screen and the center of the fog
lamp lens as shown.
2. Turn front fog lamps ON.
3. Remove front portion of fender protector(s) for adjustment screw access. Refer to
Installation of Front Fender Protector"
4. Adjust front fog lamps using adjustment screw so that the top
edge of the high intensity zone is 100 mm (4 in) below the height
of the fog lamp centers as shown.
• When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
LKIA0572E
MEL327G
MEL328G
2011 Pathfinder
HEADLAMP
EXL-145
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
UNIT REMOVAL AND INSTALLATION
HEADLAMP
Bulb Replacement
INFOID:0000000006247708
CAUTION:
Leaving bulb removed from the headlamp housing for a long period of time can deteriorate the perfor-
mance of the lens and reflector (dirt, clouding). Always prepare a new bulb and have it on hand when
replacing a bulb.
HEADLAMP
Removal
NOTE:
Reach through engine room for bulb replacement access.
1. Turn front headlamp switch OFF.
2. Disconnect the electrical connector.
3. Rotate the headlamp bulb retaining ring counterclockwise and remove.
4. Pull the headlamp bulb straight out from the front combination lamp.
CAUTION:
Grasp only the plastic base when handling the bulb. Never touch the glass envelope.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing bulb, be sure to install the bulb socket and plastic cap securely to ensure watertight-
ness.
FRONT TURN SIGNAL/PARKING LAMP
Removal
NOTE:
Reach through engine room for bulb replacement access.
1. Turn the bulb socket counterclockwise to unlock it.
2. Pull the bulb to remove it from the socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, be sure to install the bulb socket securely to ensure watertightness.
FRONT SIDE MARKER LAMP
Removal
NOTE:
Reach through engine room for bulb replacement access.
1. Turn the bulb socket counterclockwise to unlock it.
2. Pull the bulb to remove it from the socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, be sure to install the bulb socket securely to ensure watertightness.
Removal and Installation
INFOID:0000000006247709
FRONT COMBINATION LAMP
Removal
1. Remove front portion of front fender protector. Refer to
EXT-25, "Removal and Installation of Front Fender
.
2011 Pathfinder
EXL-146
< UNIT REMOVAL AND INSTALLATION >
HEADLAMP
2. Remove the front bumper. Refer to
EXT-15, "Removal and Installation"
.
3. Remove the front combination lamp bolts.
4. Disconnect the front combination lamp connector and remove front combination lamp.
Installation
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000006247710
FRONT COMBINATION LAMP
DISASSEMBLY
CAUTION:
Leaving bulb removed from the headlamp housing for a long period of time can deteriorate the perfor-
mance of the lens and reflector (dirt, clouding). Always prepare a new bulb and have it on hand when
replacing a bulb.
1. Rotate headlamp bulb retaining ring counterclockwise and remove.
CAUTION:
Grasp only the plastic base when handling headlamp bulb. Never touch the glass envelope.
2. Turn front turn signal/parking lamp bulb socket counterclockwise to unlock and remove socket.
3. Turn front side marker lamp bulb socket counterclockwise to unlock and remove socket.
ASSEMBLY
Installation is in the reverse order of removal.
CAUTION:
After installing bulb, be sure to install the bulb socket and plastic cap securely to ensure watertight-
ness.
Front combination lamp bolts ·: 6.0 Nm (0.61 kg-m, 53 in-lb)
AWLIA1816ZZ
1. Front combination lamp
2. Headlamp bulb
3. Headlamp bulb retaining ring
4. Wiring harness assembly
5. Front side marker lamp bulb
6. Front turn signal/parking lamp bulb
7.
Headlamp bulb sealing ring
2011 Pathfinder
OPTICAL SENSOR
EXL-147
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
OPTICAL SENSOR
Removal and Installation
INFOID:0000000006247711
REMOVAL
1. Remove the optical sensor and bezel from the center of the instrument panel.
2. Disconnect the optical sensor connector.
3. Remove the optical sensor from the bezel.
INSTALLATION
Installation is in the reverse order of removal.
2011 Pathfinder
EXL-148
< UNIT REMOVAL AND INSTALLATION >
FRONT FOG LAMP
FRONT FOG LAMP
Bulb Replacement
INFOID:0000000006247712
1. Partially remove the front portion of the fender protector. Refer to
EXT-25, "Removal and Installation of
.
2. Disconnect fog lamp connector.
3. Turn the bulb counterclockwise to remove it.
WARNING:
• Do not touch bulb by hand while it is lit or right after being
turned off. Burning may result.
CAUTION:
• Do not touch the glass of bulb directly by hand. Keep
grease and other oily substances away from it.
• Do not leave bulb out of fog lamp reflector for a long time
because dust, moisture smoke, etc. may affect the perfor-
mance of fog lamp. When replacing bulb, be sure to
replace it with new one.
Removal and Installation
INFOID:0000000006247713
FRONT FOG LAMP
NOTE:
The fog lamp is a semi-sealed beam type which uses a replaceable.
Removal
1. Partially remove the front portion of the front fender protector. Refer to
EXT-25, "Removal and Installation
2. Disconnect fog lamp connector.
3. Remove fog lamp screws and pull fog lamp rearward out of front
bumper.
CAUTION:
• Do not leave fog lamp assembly without bulb for a long
period of time. Dust, moisture, smoke, etc. entering the
fog lamp body may affect the performance. Remove the
bulb from the fog lamp assembly just before replacement
bulb is installed.
• Grasp only the plastic base when handling the bulb.
Never touch the glass envelope. Touching the glass could
significantly affect the bulb life and/or fog lamp perfor-
mance.
Installation
Installation is in the reverse order of removal.
NOTE:
After installation, perform front fog lamp aiming adjustment. Refer to
EXL-143, "FRONT FOG LAMP : Aiming
.
LKIA0573E
LKIA0574E
2011 Pathfinder
LIGHTING & TURN SIGNAL SWITCH
EXL-149
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation
INFOID:0000000006247714
REMOVAL
1. Remove instrument lower panel LH. Refer to
2. Remove steering column cover.
3. Disconnect the lighting and turn signal switch connector.
4. While pressing tabs, pull lighting and turn signal switch toward
driver door and release from the steering column.
INSTALLATION
Installation is in the reverse order of removal.
LKIA0013E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст