Nissan Pathfinder (2011 year). Instruction — part 643
PRECAUTION
WW-69
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
2011 Pathfinder
WW-70
< REMOVAL AND INSTALLATION >
FRONT WIPER AND WASHER SYSTEM
REMOVAL AND INSTALLATION
FRONT WIPER AND WASHER SYSTEM
Removal and Installation
INFOID:0000000006247935
FRONT WIPER ARMS
Removal
1. Remove wiper arm covers and wiper arm nuts.
2. Remove front RH wiper arm and front LH wiper arm.
3. Remove front RH and LH blade assembly from the front RH and LH arm assembly.
Installation
1. Operate wiper motor one full cycle, then turn "OFF" (Auto Stop).
2. Clean up the pivot area as shown. This will reduce possibility of
wiper arm looseness.
3. Install front RH and LH blade assembly on the front RH and LH arm.
4. Install front RH wiper arm and front LH wiper arm.
5. Ensure that wiper blades stop within proper clearance.
FRONT WIPER ARM ADJUSTMENT
1. Operate windshield washer and wiper motor one full cycle, then turn "OFF" (Auto Stop).
2. Lift the wiper blade up and then rest it onto glass surface, check
the blade clearance "L1" and "L2".
3. Remove wiper arm covers and wiper arm nuts.
4. Adjust front wiper arms on wiper motor pivot shafts to obtain
above specified blade clearances.
5. Tighten wiper arm nuts to specified torque, and install wiper arm
covers.
SEL024J
Clearance "L1"
: 24.5 - 39.5 mm (0.965 - 1.555 in)
Clearance "L2"
: 23.5 - 38.5 mm (0.925 - 1.516 in)
Front wiper arm nuts : 23.5 N·m (2.4 kg-m, 17 ft-lb)
SEL543TA
2011 Pathfinder
FRONT WIPER AND WASHER SYSTEM
WW-71
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER MOTOR AND LINKAGE
Removal
1. Remove the cowl top. Refer to
EXT-21, "Removal and Installation"
.
2. Remove wiper frame bolts, disconnect the wiper motor connec-
tor and remove the wiper frame assembly.
3. Remove wiper motor from wiper frame assembly.
Installation
CAUTION:
• Do not drop the wiper motor or cause it to contact other parts.
• Check the grease conditions of the motor arm and wiper link joint(s). Apply grease if necessary.
1. Connect wiper motor to connector. Turn the wiper switch ON to operate wiper motor, then turn the wiper
switch OFF (auto stop).
2. Disconnect wiper motor electrical connector.
3. Install wiper motor to wiper frame assembly, and install wiper frame assembly.
4. Connect wiper motor electrical connector.
5. Install cowl top. Refer to
EXT-21, "Removal and Installation"
AWKIA1471ZZ
1. Wiper arm covers
2. Front LH wiper arm and blade assembly 3. Wiper frame assembly
4. Wiper motor
5. Front RH wiper arm and blade assembly A. Wiper arm nuts
B. Wiper arm frame bolts
C. Wiper motor bolts
D. Wiper motor pivot arm bolt
LKIA0534E
2011 Pathfinder
WW-72
< REMOVAL AND INSTALLATION >
FRONT WIPER AND WASHER SYSTEM
WASHER HOSE LAYOUT
WASHER NOZZLES
Removal
1. Remove the cowl top. Refer to
EXT-21, "Removal and Installation"
.
2. Remove washer nozzles.
Installation
Installation is in the reverse order of removal.
WIPER AND WASHER SWITCH
Removal
1. Remove instrument lower cover LH. Refer to
2. Remove steering column cover lower and steering column cover upper.
3. Disconnect wiper and washer switch connector.
4. Pinch tabs at wiper and washer switch base and slide switch
away from steering column.
Installation
Installation is in the reverse order of removal.
WASHER FLUID RESERVOIR
Removal
1. Remove the front fender protector RH. Refer to
EXT-25, "Removal and Installation of Front Fender Pro-
WKIA4139E
1.
Rear washer nozzle
2.
Washer nozzles
3.
Washer fluid reservoir
WKIA0071E
2011 Pathfinder
FRONT WIPER AND WASHER SYSTEM
WW-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
2. Remove clip, then remove washer fluid reservoir filler neck from
washer fluid reservoir.
3. Disconnect front and rear washer hoses.
4. Disconnect front and rear washer motor connector.
5. Disconnect washer fluid level sensor connector.
6. Remove washer fluid reservoir screws and remove washer fluid
reservoir.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installation, add water up to the upper level of the washer fluid reservoir inlet and check for water
leaks.
WASHER MOTOR
Removal
1. Remove RH front fender protector. Refer to
EXT-25, "Removal and Installation of Front Fender Protector"
.
2. Disconnect the front washer hoses.
3. Disconnect the front washer motor connectors.
LKIA0538E
LKIA0537E
LKIA0539E
2011 Pathfinder
WW-74
< REMOVAL AND INSTALLATION >
FRONT WIPER AND WASHER SYSTEM
4. Slide retaining ring upward to release front and rear washer
motor.
5. Remove front washer motor from washer fluid reservoir.
Installation
Installation is in the reverse order of removal.
CAUTION:
When installing front washer motor, there should be no packing twists, etc.
WASHER FLUID LEVEL SENSOR
Removal
1. Remove washer fluid reservoir.
2. Lift level sensor out of washer fluid reservoir in the direction of
the arrow as shown.
Installation
Installation is in the reverse order of removal.
Washer Nozzle Adjustment
INFOID:0000000006247936
• This vehicle is equipped with non-adjustable washer nozzles.
• If not satisfied with washer fluid spray coverage, confirm that the
washer nozzle is installed correctly.
• If the washer nozzle is installed correctly, and the washer fluid
spray coverage is not satisfactory, replace the washer nozzle.
LKIA0540E
LKIA0541E
PKIA2552E
2011 Pathfinder
REAR WIPER AND WASHER SYSTEM
WW-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER AND WASHER SYSTEM
Removal and Installation
INFOID:0000000006247937
REAR WIPER ARM
Removal
1. Remove wiper arm cover, and remove rear wiper arm nut.
2. Remove the wiper arm.
3. Remove wiper blade from the wiper arm.
Installation
1. Operate rear wiper motor one full cycle, then turn "OFF" (Auto Stop).
2. Clean pivot area as shown. This will reduce the possibility of
wiper arm looseness.
3. Install wiper blade on the wiper arm.
4. Install wiper arm so that the arm rests in the stopper and tighten rear wiper arm nut.
5. Install wiper arm cover.
REAR WIPER MOTOR
LKIA0608E
SEL024J
2011 Pathfinder
WW-76
< REMOVAL AND INSTALLATION >
REAR WIPER AND WASHER SYSTEM
Removal
1. Remove wiper arm. Refer to
WW-75, "Removal and Installation"
.
2. Remove pivot cap.
3. Remove rear wiper motor nut.
4. Remove rear wiper motor cover.
5. Disconnect rear wiper motor connector.
6. Remove nut and remove rear wiper motor.
7. Remove rear wiper motor cover base.
8. Remove bracket.
Installation
CAUTION:
• Do not drop the wiper motor or cause it to contact other parts.
Installation is in the reverse order of removal.
1.
Rear wiper motor cover
2.
Rear wiper motor
3.
Plate
4.
Rear wiper motor cover base
5.
Spacer
6.
Bracket
7.
Grommet
8.
Washer
9.
Rear wiper motor nut
10. Pivot cap
11. Rear wiper arm and blade
12. Wiper arm nut
13. Wiper arm cover
14. Cap nut
15. Gasket
16. Gasket
17. Stud
18. Grommet
19. Nut
AWLIA1808ZZ
LKIA0543E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст