Nissan Pathfinder (2011 year). Instruction — part 156
DLK-114
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
IGNITION KNOB SWITCH
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Replace key switch and ignition knob switch.
4.
CHECK IGNITION KNOB SWITCH CIRCUIT
1. Check continuity between Intelligent Key unit harness connector (A) M164 terminal 27 and key switch and
ignition knob switch harness connector (B) M66 terminal 2.
2. Check continuity between Intelligent Key unit harness connector
M164 terminal 27 and ground.
Is the inspection result normal?
YES
>> Check the condition of harness and harness connector.
NO
>> Repair or replace harness between Intelligent Key unit
and key switch and ignition knob switch.
Component
Terminals
Condition
Continuity
Ignition
knob switch
1
2
Ignition switch is pushed
Yes
Ignition switch is released
No
ALKIA1218ZZ
27 - 2
: Continuity should exist.
27 - Ground
: Continuity should not exist.
ALKIA1219ZZ
2011 Pathfinder
HEADLAMP FUNCTION
DLK-115
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HEADLAMP FUNCTION
Diagnosis Procedure
INFOID:0000000006245535
1.
CHECK HEADLAMP OPERATION
Do headlamps operate with headlamp switch?
YES or NO
YES
>> Headlamp circuit is OK.
NO
>> Check headlamp circuit. Refer to
2011 Pathfinder
DLK-116
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
Diagnosis Procedure
INFOID:0000000006245536
1.
CHECK MAP LAMP OPERATION
When room lamp switch is in "DOOR" position, open the driver or passenger door.
Map lamp and ignition keyhole illumination should illuminate.
Is the inspection result normal?
YES
>> Map lamp circuit is OK.
NO
>> Check map lamp circuit. Refer to
.
2011 Pathfinder
KEYFOB ID SET UP WITH CONSULT-III
DLK-117
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID SET UP WITH CONSULT-III
ID Code Entry Procedure
INFOID:0000000006245537
KEYFOB ID SET UP WITH CONSULT-III
NOTE:
•
If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-
cific ID code can be erased with CONSULT-III. However, when the ID code of a lost keyfob is not
known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all
remaining and/or new keyfobs must be re-registered.
•
When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If
five ID codes are stored in memory when an additional code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the new
ID code is added and no ID codes are erased.
•
Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest ID
code will be erased.
•
Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
1. Turn ignition switch ON.
2. Select “BCM”.
3. Select “MULTI REMOTE ENT”.
4. Select “WORK SUPPORT”.
5. You can register, erase or confirm a keyfob ID code. To register a new code, select the following option
and follow CONSULT-III instructions:
• “REMO CONT ID REGIST”
Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or when additional keyfob is required.
• “REMO CONT ID ERASUR”
Use this mode to erase a keyfob ID code.
• “REMO CONT ID CONFIR”
Use this mode to confirm if a keyfob ID code is registered or not.
2011 Pathfinder
DLK-118
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITHOUT CONSULT-III
KEYFOB ID SET UP WITHOUT CONSULT-III
ID Code Entry Procedure
INFOID:0000000006245538
KEYFOB ID SET UP WITHOUT CONSULT-III
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A specific ID
code can be erased with CONSULT-III. However, when the ID code of a lost keyfob is not known, all control-
LIIA1670E
2011 Pathfinder
KEYFOB ID SET UP WITHOUT CONSULT-III
DLK-119
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ler ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new key-
fobs must be re-registered.
To erase all ID codes in memory, register one ID code (keyfob) five times. After all ID codes are erased, the
ID codes of all remaining and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If five ID
codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less
than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added
and no ID codes are erased.
• If you need to activate more than two additional new keyfobs, repeat the procedure “Additional ID code
entry” for each new keyfob.
• Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code
will be erased.
• Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is
counted as an additional code.
2011 Pathfinder
DLK-120
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HOMELINK UNIVERSAL TRANSCEIVER
HOMELINK UNIVERSAL TRANSCEIVER
Description
INFOID:0000000006245540
Homelink universal transceiver can store and transmit a maximum of 3 radio signals.
Allows operation of garage doors, gates, home and office lighting, entry door locks and security system, etc.
Homelink universal transceiver power supply uses vehicle battery, which enables it to maintain every program
in case battery is discharged or removed.
Component Function Check
INFOID:0000000006245541
1.
CHECK FUNCTION
Check that system receiver (garage door opener, etc.) operates with original hand-held transmitter.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Receiver or hand-held transmitter is malfunctioning.
2.
CHECK ILLUMINATION
1. Turn ignition switch “OFF”.
2. Press each of the transmitter buttons and watch for the red light
to illuminate with each button.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Refer to
DLK-120, "Diagnosis Procedure"
.
3.
CHECK TRANSMITTER
Check transmitter with Tool*.
*:For details, refer to Technical Service Bulletin.
Is the inspection result normal?
YES
>> Receiver or hand-held transmitter malfunction, not vehicle related.
NO
>> Replace auto anti-dazzling inside mirror (homelink universal transceiver).
Diagnosis Procedure
INFOID:0000000006245542
Regarding Wiring Diagram information, refer to
.
1.
CHECK POWER SUPPLY
1. Disconnect auto anti-dazzling inside mirror (homelink universal transceiver) connector.
2. Check voltage between auto anti-dazzling inside mirror
(homelink universal transceiver) harness connector and ground.
PIIA4815E
ALKIA0426ZZ
2011 Pathfinder
HOMELINK UNIVERSAL TRANSCEIVER
DLK-121
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check the following.
• 10A fuse [No. 19 located in the fuse block (J/B)]
• Harness for open or short between fuse and auto anti-dazzling inside mirror (homelink universal
transceiver).
2.
CHECK GROUND CIRCUIT
Check continuity between auto anti-dazzling inside mirror (homelink
universal transceiver) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair harness.
3.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
.
>> Inspection End.
Auto anti-dazzling inside mirror
(Homelink universal transceiver)
connector
Terminal Condition
Voltage (V)
(Approx.)
R7
10
Ground
Ignition switch position: LOCK
Battery voltage
ALKIA1245ZZ
Auto anti-dazzling inside mirror
(Homelink universal transceiver) connector
Terminal
Ground
Continuity
R7
3
Yes
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст