Nissan Pathfinder (2011 year). Instruction — part 535
SE-38
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
1.
Headrest
2.
Seatback assembly
3.
Headrest holder
4.
Headrest holder with multi position
lock
5.
Seatback board
6.
Power seat cushion rear finisher
7.
Leg Cover
8.
Lifter motor link bar
9.
Seat belt buckle assembly
10. Seat cushion inner finisher
11. Seat frame assembly
12. Seat lifter motor assembly
13. Seat spacer
14. Lock gear
15. Seat cushion front finisher
16. Flexible seat wire
17. Front seat slide motor assembly (LH) 18. Power seat control assembly
19. Lifter motor bracket assembly
20. Driver seat wiring harness
21. Seat cushion outer finisher
22 Leg cover
23 Bolt cover
24. Seat cushion frame
25. Recliner switch knob
26. Slide switch knob
27. Power seat switch escutcheon
28. Switch assembly
29. Seat cushion pad
30. Seat cushion heating element
31. Seat cushion trim
32. Seat cushion assembly
33. Lumbar support lever knob
34. Snap ring
2011 Pathfinder
FRONT SEAT
SE-39
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Instruction Driver Seat
AWJIA0551ZZ
1.
Headrest
2.
Trim clip
3.
Seatback assembly
4.
Seat cushion trim cover
5.
Seat cushion pad
6.
Snap ring
7.
Seat cushion frame
8.
Seat cushion inner finisher
9.
Seat belt buckle assembly
10. Seat frame assembly
11. Leg cover
12. Bolt cover
13. Recline lever
14. Seat cushion outer finisher
15. Leg cover
16. Seat cushion rear finisher
17. Seat cushion lift knobs
18. Seatback board
2011 Pathfinder
SE-40
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Conventional Passenger Seat
19. Headrest holder with multi position
lock
20. Headrest holder
21. Lumbar support lever knob
22 Snap ring
AWJIA0552ZZ
1.
Damper assembly
2.
Headrest
3.
Seatback assembly
4.
Switch assembly
5.
Power seat switch escutcheon
6.
Recliner switch knob
7.
Slide switch knob
8.
Seat cushion assembly
9.
Seat cushion outer cover
10. Leg cover
11. Seat cushion front finisher
12. Passenger seat wiring harness
13. Power seat frame assembly
14. Seat cushion inner finisher
15. Seat belt buckle assembly
16. Leg cover
17. Seat cushion rear finisher
18. Instruction seat frame assembly
2011 Pathfinder
FRONT SEAT
SE-41
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Fold Flat Passenger Seat
Seatback Assembly
INFOID:0000000006247162
REMOVAL
CAUTION:
19. Recline lever
20. Seat cushion rear finisher
21. Seatback board
22. Headrest holder with multi position
lock
23. Headrest holder
AWJIA0553ZZ
1.
Front seatback lever
2.
Trim clip
3.
Headrest
4.
Seatback assembly
5.
Seat cushion assembly
6.
Seat cushion outer finisher
7.
Leg cover
8.
Seat frame assembly
9.
Passenger seat wiring harness
10. Seat cushion inner cover
11. Leg cover
12. Seat belt buckle assembly
13. Inboard reclining arm outer cover
14. Inboard reclining arm inner cover
15. Outboard reclining arm inner cover
16. Outboard reclining arm outer cover
17. Seat cushion rear finisher
18. Seatback board
19. Headrest holder with multi position
lock
20. Headrest holder
2011 Pathfinder
SE-42
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Seats equipped with side air bags can only be serviced as an assembly.
1. Remove the seat assembly. Refer to
SE-33, "Removal and Installation"
.
2. Unzip the seatback trim flap (1).
3. Unclip the lower retainer (2).
4. For the passenger seatback, remove the seatback board from the seatback. Refer to
.
5. Unclip the seatback trim j-clips.
6. Remove the bolts (two for each side) and the seatback assem-
bly.
DISASSEMBLY
CAUTION:
Seats equipped with side air bags can only be serviced as an assembly.
1. Remove the seatback assembly.
2. Remove the headrest.
LIIA2419E
SIIA0113E
LIIA2420E
2011 Pathfinder
FRONT SEAT
SE-43
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3. From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
4. Remove the snap ring and the lumbar support lever knob.
5. Remove the seatback trim and pad assembly.
6. Remove the hog rings to separate the seatback trim from the pad and the heating element (if equipped).
ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTALLATION
Installation is in the reverse order of removal.
Passenger Seatback Board
INFOID:0000000006247163
SOFT SEATBACK
Removal
1. The seatback board is attached to the seat frame with the follow-
ing:
• Two top tabs (A)
• Two side tabs (B)
• Two bottom clips (C) (must be replaced)
2. Move seat to forward position.
LRS023
PIIA1156E
ALIIA0366ZZ
2011 Pathfinder
SE-44
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
3. Hold the seatback board as shown and pull the top of the seat-
back board away from the seat back frame.
4. Pull the middle part of the seatback board to disengage the side
tabs (A) from the seatback frame.
5. Pull the lower part of the seatback board to disengage the bot-
tom clips from the seatback frame.
Installation
Installation is in the reverse order of removal.
HARD SEATBACK
Removal
1. The seatback board is attached to the seat frame with the follow-
ing:
• Two top tabs (A)
• Two side tabs (B)
• Two bottom clips (C) (must be replaced)
2. Move seat to forward position.
3. Hold the seatback board as shown and pull the bottom of the
seatback board away from the seat back frame.
ALIIA0368ZZ
ALIIA0367ZZ
ALIIA0369ZZ
ALIIA0370ZZ
2011 Pathfinder
FRONT SEAT
SE-45
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4. Pull the middle part of the seatback board to disengage the side
tabs (A) from the seatback frame.
5. Lift the upper part of the seatback board to disengage the top
tabs from the seatback frame.
Installation
Installation is in the reverse order of removal.
Seat Cushion Trim and Pad
INFOID:0000000006247164
REMOVAL
CAUTION:
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
• When removed, the passenger seat cushion must always be placed pan side UP to prevent damage.
• During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do
not add additional clips.
• The Occupant Classification System control module can only be replaced as part of the seat cushion
assembly.
1. Remove the front seat assembly. Refer to
SE-33, "Removal and Installation"
.
2. Remove the power seat switch knobs and power seat switch
escutcheon (if equipped) or lift knobs on instruction seats.
3. Remove the seat cushion outer finisher.
4. Remove the power seat switch screws.
5. Remove four bolts and the seat cushion assembly.
ALIIA0371ZZ
LIIA0681E
LIIA0285E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст