Nissan Pathfinder (2011 year). Instruction — part 469
INT-16
< REMOVAL AND INSTALLATION >
DOOR FINISHER
a. While pushing on the side of the armrest, pull up on the rear of the armrest releasing the lower fastening
points.
b. With the rear of the armrest pulled upward, pull the front of the armrest toward you and remove.
5. Remove the screws behind armrest.
6. Release clips and reposition front door finisher.
7. Remove the pull handle/lock lever assembly.
8. Disconnect lock cable and handle cable from door handle assembly. Refer to
.
9. Remove the memory seat switch (if equipped).
• Disconnect the harness connector.
10. Remove the door finisher.
Installation
Installation is in the reverse order of removal.
REAR DOOR
Removal
1. Remove the power window switch assembly.
• Disconnect the harness connector.
2. Remove the pull handle cover.
• Remove the screw behind the pull handle cover.
3. Remove the pull handle escutcheon.
1.
Rear door
2.
Rear door tweeter
3.
Pull handle/lock lever assembly
4.
Pull handle escutcheon
5.
Pull handle cover
6.
Metal clip
7.
Power window switch assembly
8.
Armrest
9.
Rear door finisher (RH shown)
10. Rear door handle bracket
A.
Clip
ALJIA0644GB
2011 Pathfinder
DOOR FINISHER
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
4. Lift upward to release clips and remove the armrest.
• Remove the screws behind armrest.
5. Release the clips and remove the rear door finisher.
• Disconnect the rear door tweeter connector, then remove the rear door tweeter screws and remove the
rear door tweeter.
6. Remove pull handle/lock lever assembly.
• Disconnect lock lever cable and pull handle cable from lever assembly.
Installation
Installation is in the reverse order of removal.
2011 Pathfinder
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Component
INFOID:0000000006243561
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear kick plate
5.
Access cover (RH side only)
6.
Center pillar lower finisher
7.
Front kick plate
8.
Lower dash side finisher
9.
Front door welt
10. Front pillar lower finisher
11. Front pillar upper finisher
12. Front pillar assist grip
13. LH side demister grille
14. Molded plastic clip
15. Garnish
C.
Clip C101
D.
Clip C111
E.
Metal clip
Vehicle front
AWJIA0051GB
2011 Pathfinder
BODY SIDE TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000006243562
LOWER DASH SIDE FINISHER
Removal
1. Remove front kick plate. Refer to the KICK PLATES procedure in this section.
2. Remove the push pin from lower dash side finisher.
3. Remove the lower dash side finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
Removal
1. Partially remove front and rear door welts as necessary.
2. Remove the seat belt anchor. Refer to
SB-12, "Removal and Installation"
• On RH side, disconnect seat belt tension sensor.
3. Remove the front and rear kick plates. Refer to the KICK PLATES procedure in this section.
4. Remove the center pillar lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1. Remove the center pillar lower finisher. Refer to CENTER PILLAR LOWER FINISHER procedure in this
section.
2. Remove the bolts then assist grip.
3. Remove the clips and bolts, then center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR UPPER FINISHER
Removal
1. Remove the front pillar lower finisher. Refer to FRONT PILLAR LOWER FINISHER procedure in this sec-
tion.
2. Remove the bolts, then front pillar assist grip.
3. Remove the front pillar upper finisher bolt.
4. Remove the front pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR LOWER FINISHER
Removal
1. Partially remove the front door welt.
2. Remove the front kick plate. Refer to KICK PLATES procedure in this section.
3. Release the clips, then remove the front pillar lower finisher.
Installation
Installation is in the reverse order of removal.
KICK PLATES
Removal
Release clips and remove the front and/or rear kick plates.
Installation
2011 Pathfinder
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
Installation is in the reverse order of removal.
2011 Pathfinder
FLOOR TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Removal and Installation
INFOID:0000000006243563
Front and Rear Floor Carpet
REMOVAL
Front Carpet
1. Remove the front seats. Refer to
SE-33, "Removal and Installation"
.
2. Remove the lower seat belt anchors. Refer to
SB-12, "Removal and Installation"
3. Remove the lower body side trim panels. Refer to
INT-19, "Removal and Installation"
4. Remove the center console. Refer to
IP-12, "Removal and Installation"
.
5. Remove the floor mat hooks from the front carpet.
6. Remove the front carpet.
Rear Carpet
1. Remove the second and third row seats. Refer to
SE-35, "Removal and Installation"
.
2. Remove the luggage side lower finisher RH and LH. Refer to
INT-25, "Removal and Installation"
.
3. Remove the flipper doors and the floor tray. Refer to
INT-25, "Removal and Installation"
4. Remove the bolts and the storage box. Refer to
INT-25, "Removal and Installation"
5. Remove the rear carpet.
INSTALLATION
Installation is in the reverse order of removal.
AWJIA0411ZZ
1.
Front carpet
2.
Floor mat hooks
3.
Rear carpet
A.
Clip C103
Vehicle front
2011 Pathfinder
INT-22
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Removal and Installation
INFOID:0000000006243564
REMOVAL
1. Remove the body side trim panels. Refer to
.
2. Remove the luggage floor trim upper panels. Refer to
.
3. Remove the sun visor assemblies, both LH and RH.
1.
Sun visor holder LH/RH
2.
Sun visor assembly RH
3.
Front assist grip RH
4.
Rear assist grip RH
5.
Front roof console with front room
lamp assembly and sunglass bin
6.
Sunroof welt (if equipped)
7.
DVD video monitor finisher (if
equipped)
8.
Center room lamp assembly
9.
Rear room lamp assembly
10. Rear assist grip LH
11. Headlining
12. Sun visor assembly LH
A.
Clip C103
Vehicle front
Metal clip
AWJIA0052GB
2011 Pathfinder
HEADLINING
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
4. Insert a suitable thin tool (A) at approximately a 30 degree angle
into the sun visor holder notch on the front of the sun visor
holder (1) and press in the locking tab (B) to release it. While
holding in lock tab (B), turn the sun visor holder (1) 90 degrees
to release it from the headliner.
• If the sun visor holder (1) does not fully rotate, make sure that
the suitable thin tool (A) is pressing in on the locking tab (B)
and is not positioned under locking tab (B). Reinsert the suit-
able thin tool (A) as necessary to release the locking tab (B).
•
: Front
CAUTION:
Do not force the sun visor holder when removing as the
locking tab may be damaged if the suitable thin tool is not
positioned correctly.
5. Remove the sunroof welt (if equipped).
6. Remove the DVD video monitor assembly (if equipped). Refer to
AV-267, "Removal and Installation of
(BOSE audio without navigation) and
AV-428, "Removal and Installation of Video Monitor"
(BOSE audio with navigation).
• Disconnect the harnesses.
7. Remove the front and rear RH and LH assist grips.
8. Release the front roof console clips, using a suitable tool and remove the front roof console.
• Disconnect the harness.
9. Remove the center room and the rear room lamp assemblies.
10. Remove the rear upper overhead duct (if equipped). Refer to
VTL-33, "Removal and Installation"
11. Remove the headlining.
NOTE:
Use an assistant to steady the headlining while lowering from roof.
• Remove the clips from center of headlining.
• Remove the clips from rear of headlining.
• Disconnect the rear washer tube at front connection, allow to drain.
• Disconnect the harnesses and rear washer tube rear connections.
12. Remove the overhead grilles, then transfer them to the new headlining.
13. Remove the assist grip brackets from the roof.
INSTALLATION
Installation is in the reverse order of removal.
ALJIA0537ZZ
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст