Nissan Pathfinder (2011 year). Instruction — part 245
EC-14
< BASIC INSPECTION >
[VQ40DE]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Trouble Diagnosis Introduction
INFOID:0000000006243741
INTRODUCTION
The engine has an ECM to control major systems such as fuel con-
trol, ignition control, idle air control system, etc. The ECM accepts
input signals from sensors and instantly drives actuators. It is essen-
tial that both input and output signals are proper and stable. At the
same time, it is important that there are no malfunctions such as vac-
uum leaks, fouled spark plugs, or other malfunctions with the engine.
It is much more difficult to diagnose an incident that occurs intermit-
tently rather than continuously. Most intermittent incidents are
caused by poor electric connections or improper wiring. In this case,
careful checking of suspected circuits may help prevent the replace-
ment of good parts.
A visual check only may not find the cause of the incidents. A road
test with CONSULT-III (or GST) or a circuit tester connected should
be performed. Follow the Work Flow on "Work Flow".
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such incidents, especially
intermittent ones. Find out what symptoms are present and under
what conditions they occur. A Diagnostic Worksheet like the example
on "Worksheet Sample" should be used.
Start your diagnosis by looking for conventional malfunctions first.
This will help troubleshoot driveability malfunctions on an electroni-
cally controlled engine vehicle.
WORK FLOW
Overall Sequence
MEF036D
SEF233G
SEF234G
2011 Pathfinder
DIAGNOSIS AND REPAIR WORKFLOW
EC-15
< BASIC INSPECTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Detailed Flow
1.
GET INFORMATION FOR SYMPTOM
*1: Include 1st trip DTC.
*2: Include 1st trip freeze frame data.
JSBIA0067GB
2011 Pathfinder
EC-16
< BASIC INSPECTION >
[VQ40DE]
DIAGNOSIS AND REPAIR WORKFLOW
1. Get the detailed information from the customer about the symptom (the condition and the environment
when the incident/malfunction occurred) using the “Diagnostic Work Sheet”.
2. Ask if the customer requests I/M examination.
Malfunction information, obtained>>GO TO 2.
No malfunction information, but a request for I/M examination>>GO TO 13.
2.
CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is displayed.
-
Record DTC and freeze frame data. (Print them out with CONSULT-III or GST.)
-
Erase DTC. Refer to
EC-74, "On Board Diagnosis Function"
(Without CONSULT-III) or
(With CONSULT-III).
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
(Symptom Table is useful. Refer to
EC-472, "Symptom Matrix Chart"
3. Check related service bulletins for information.
Are any symptoms described and any DTCs detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer (except MIL ON).
Also study the normal operation and fail-safe related to the symptom.
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the displayed DTC, and then make sure that DTC is
detected again.
If two or more DTCs are detected, refer to
EC-440, "DTC Inspection Priority Chart"
and determine trouble
diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Instruction. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 10.
NO
>> Check according to
.
6.
PERFORM BASIC INSPECTION
Perform
.
Do you have CONSULT-III?
YES
>> GO TO 7.
NO
>> GO TO 9.
2011 Pathfinder
DIAGNOSIS AND REPAIR WORKFLOW
EC-17
< BASIC INSPECTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
7.
PERFORM SPEC IN DATA MONITOR MODE
With CONSULT-III
Make sure that “MAS A/F SE-B1”, “MAS A/F SE-B2”, “B/FUEL SCHDL”, “A/F ALPHA-B1”, and “A/F ALPHA-
B2” are within the SP value using CONSULT-III “SPEC” in “DATA MONITOR” mode. Refer to
Is the measurement value within the SP value?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART BY TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Detect malfunctioning part according to
Is a malfunctioning part detected?
YES
>> GO TO 11.
NO
>> GO TO 9.
9.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to
EC-472, "Symptom Matrix Chart"
based on the confirmed symptom
in step 4, and determine the trouble diagnosis order based on possible causes and symptoms.
>> GO TO 10.
10.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
NOTE:
The Diagnosis Procedure in EC section described based on open circuit inspection. A short circuit inspection
is also required for the circuit check in the Diagnosis Procedure. For details, refer to
Is a malfunctioning part detected?
YES
>> GO TO 11.
NO
>> Monitor input data from related sensors or check voltage of related ECM terminals using CON-
SULT-III. Refer to
EC-430, "ECM Terminal and Reference Value"
,
ence Value in Data Monitor Mode"
.
11.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it. Refer to
EC-74, "On Board Diagnosis Function"
(Without CON-
SULT-III) or
(With CONSULT-III).
>> GO TO 12.
12.
FINAL CHECK
When DTC was detected in step 2, perform DTC CONFIRMATION PROCEDURE or Component Function
Check again, and then make sure that the malfunction have been completely repaired.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and make sure
that the symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 10.
YES-2 >> Symptom remains: GO TO 6.
NO-1 >> No request for I/M examination from the customer: Before returning the vehicle to the customer,
always erase unnecessary DTC in ECM and TCM (Transmission Control Module). Refer to
74, "On Board Diagnosis Function"
and
TM-36, "CONSULT-III Function (TRANSMISSION)"
(With CONSULT-III).
NO-2 >> I/M examination, requested from the customer: GO TO 13.
13.
PREPARE FOR I/M EXAMINATION
1. Set SRT codes. Refer to
.
2011 Pathfinder
EC-18
< BASIC INSPECTION >
[VQ40DE]
DIAGNOSIS AND REPAIR WORKFLOW
2. Erase permanent DTCs. Refer to
>> INSPECTION END
DIAGNOSTIC WORKSHEET
Description
There are many operating conditions that lead to the malfunction of
engine components. A good grasp of such conditions can make trou-
bleshooting faster and more accurate.
In general, each customer feels differently about symptoms. It is
important to fully understand the symptoms or conditions for a cus-
tomer complaint.
Utilize a diagnostic worksheet like the one on the next page in order
to organize all the information for troubleshooting.
Some conditions may cause the MIL to illuminate or blink and DTC
to be detected. Examples:
• Vehicle ran out of fuel, which caused the engine to misfire.
• Fuel filler cap was left off or incorrectly screwed on, allowing fuel to
evaporate into the atmosphere.
SEF907L
2011 Pathfinder
DIAGNOSIS AND REPAIR WORKFLOW
EC-19
< BASIC INSPECTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Worksheet Sample
LEC031A
2011 Pathfinder
EC-20
< BASIC INSPECTION >
[VQ40DE]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
Basic Inspection
INFOID:0000000006243742
1.
INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
-
Harness connectors for improper connections
-
Wiring harness for improper connections, pinches and cut
-
Vacuum hoses for splits, kinks and improper connections
-
Hoses and ducts for leakage
-
Air cleaner clogging
-
Gasket
3. Check that electrical or mechanical loads are not applied.
-
Headlamp switch is OFF.
-
Air conditioner switch is OFF.
-
Rear window defogger switch is OFF.
-
Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no
load.
6. Make sure that no DTC is displayed with CONSULT-III or GST.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
3.
CHECK TARGET IDLE SPEED
With CONSULT-III
1. Run engine at about 2,000 rpm for about 2 minutes under no load.
SEF983U
SEF976U
SEF977U
2011 Pathfinder
INSPECTION AND ADJUSTMENT
EC-21
< BASIC INSPECTION >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2. Rev engine (2,000 to 3,000 rpm) two or three times under no
load, then run engine at idle speed for about 1 minute.
3. Read idle speed in “DATA MONITOR” mode with CONSULT-III.
EC-24, "Idle Speed and Ignition Timing Check"
.
Without CONSULT-III
1. Run engine at about 2,000 rpm for about 2 minutes under no load.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for about
1 minute.
EC-24, "Idle Speed and Ignition Timing Check"
.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 4.
4.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1. Stop engine.
2. Perform
EC-25, "Accelerator Pedal Released Position Learning"
>> GO TO 5.
5.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform
EC-25, "Throttle Valve Closed Position Learning"
.
>> GO TO 6.
6.
PERFORM IDLE AIR VOLUME LEARNING
EC-25, "Idle Air Volume Learning"
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes
>> GO TO 7.
No
>> 1. Follow the instruction of Idle Air Volume Learning.
2. GO TO 4.
7.
CHECK TARGET IDLE SPEED AGAIN
With CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Read idle speed in “DATA MONITOR” mode with CONSULT-III.
EC-24, "Idle Speed and Ignition Timing Check"
.
Without CONSULT-III
1. Start engine and warm it up to normal operating temperature.
PBIA8513J
625
±
50 rpm (in P or N position)
625
±
50 rpm (in P or N position)
625
±
50 rpm (in P or N position)
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст