Nissan Pathfinder (2011 year). Instruction — part 174
DLK-258
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEY SWITCH (BCM INPUT)
KEY SWITCH (BCM INPUT)
Diagnosis Procedure
INFOID:0000000006245654
Regarding Wiring Diagram information, refer to
DLK-279, "Wiring Diagram - Without Intelligent Key System"
1.
CHECK KEY SWITCH INPUT SIGNAL
With CONSULT-III
Check key switch "KEY ON SW" in DATA MONITOR mode with CONSULT–III. Refer to
LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
• When key is inserted to ignition key cylinder:
• When key is removed from ignition key cylinder:
Without CONSULT-III
Check voltage between BCM connector M18 terminal 37 and
ground.
Is the inspection result normal?
YES
>> Key switch (insert) circuit is OK.
NO
>> GO TO 2
2.
CHECK KEY SWITCH (INSERT)
1. Turn ignition switch OFF.
2. Disconnect key switch connector.
3. Check continuity between key switch terminals.
Is the inspection result normal?
YES
>> Repair or replace harness or fuse.
NO
>> Replace key switch.
KEY ON SW
: ON
KEY ON SW
: OFF
Connec-
tor
Terminal
Condition
Voltage (V)
(+)
(–)
M18
37
Ground
Key is inserted.
Battery voltage
Key is removed.
0
LIIA0567E
Terminals
Condition
Continuity
1 – 2
Key is inserted.
Yes
Key is removed.
No
WIIA0559E
2011 Pathfinder
HEADLAMP FUNCTION
DLK-259
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HEADLAMP FUNCTION
Diagnosis Procedure
INFOID:0000000006245655
1.
CHECK HEADLAMP OPERATION
Do headlamps operate with headlamp switch?
YES or NO
YES
>> Headlamp circuit is OK.
NO
>> Check headlamp circuit. Refer to
2011 Pathfinder
DLK-260
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
Diagnosis Procedure
INFOID:0000000006245656
1.
CHECK MAP LAMP OPERATION
When room lamp switch is in "DOOR" position, open the driver or passenger door.
Map lamp and ignition keyhole illumination should illuminate.
Is the inspection result normal?
YES
>> Map lamp circuit is OK.
NO
>> Check map lamp circuit. Refer to
.
2011 Pathfinder
KEYFOB ID SET UP WITH CONSULT-III
DLK-261
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID SET UP WITH CONSULT-III
ID Code Entry Procedure
INFOID:0000000006245657
KEYFOB ID SET UP WITH CONSULT-III
NOTE:
•
If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-
cific ID code can be erased with CONSULT-III. However, when the ID code of a lost keyfob is not
known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all
remaining and/or new keyfobs must be re-registered.
•
When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If
five ID codes are stored in memory when an additional code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the new
ID code is added and no ID codes are erased.
•
Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest ID
code will be erased.
•
Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
1. Turn ignition switch ON.
2. Select “BCM”.
3. Select “MULTI REMOTE ENT”.
4. Select “WORK SUPPORT”.
5. You can register, erase or confirm a keyfob ID code. To register a new code, select the following option
and follow CONSULT-III instructions:
• “REMO CONT ID REGIST”
Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or when additional keyfob is required.
• “REMO CONT ID ERASUR”
Use this mode to erase a keyfob ID code.
• “REMO CONT ID CONFIR”
Use this mode to confirm if a keyfob ID code is registered or not.
2011 Pathfinder
DLK-262
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITHOUT CONSULT-III
KEYFOB ID SET UP WITHOUT CONSULT-III
ID Code Entry Procedure
INFOID:0000000006245658
KEYFOB ID SET UP WITHOUT CONSULT-III
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A specific ID
code can be erased with CONSULT-III. However, when the ID code of a lost keyfob is not known, all control-
LIIA1670E
2011 Pathfinder
KEYFOB ID SET UP WITHOUT CONSULT-III
DLK-263
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ler ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new key-
fobs must be re-registered.
To erase all ID codes in memory, register one ID code (keyfob) five times. After all ID codes are erased, the
ID codes of all remaining and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If five ID
codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less
than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added
and no ID codes are erased.
• If you need to activate more than two additional new keyfobs, repeat the procedure “Additional ID code
entry” for each new keyfob.
• Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code
will be erased.
• Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is
counted as an additional code.
2011 Pathfinder
DLK-264
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOMELINK UNIVERSAL TRANSCEIVER
HOMELINK UNIVERSAL TRANSCEIVER
Description
INFOID:0000000006245660
Homelink universal transceiver can store and transmit a maximum of 3 radio signals.
Allows operation of garage doors, gates, home and office lighting, entry door locks and security system, etc.
Homelink universal transceiver power supply uses vehicle battery, which enables it to maintain every program
in case battery is discharged or removed.
Component Function Check
INFOID:0000000006245661
1.
CHECK FUNCTION
Check that system receiver (garage door opener, etc.) operates with original hand-held transmitter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Receiver or hand-held transmitter is malfunctioning.
2.
CHECK ILLUMINATION
1. Turn ignition switch “OFF”.
2. Press each of the transmitter buttons and watch for the red light
to illuminate with each button.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Refer to
DLK-264, "Diagnosis Procedure"
.
3.
CHECK TRANSMITTER
Check transmitter with Tool*.
*:For details, refer to Technical Service Bulletin.
Is the inspection result normal?
YES
>> Receiver or hand-held transmitter malfunction, not vehicle related.
NO
>> Replace auto anti-dazzling inside mirror (homelink universal transceiver).
Diagnosis Procedure
INFOID:0000000006245662
Regarding Wiring Diagram information, refer to
.
1.
CHECK POWER SUPPLY
1. Disconnect auto anti-dazzling inside mirror (homelink universal transceiver) connector.
2. Check voltage between auto anti-dazzling inside mirror
(homelink universal transceiver) harness connector and ground.
PIIA4815E
ALKIA0426ZZ
2011 Pathfinder
HOMELINK UNIVERSAL TRANSCEIVER
DLK-265
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Check the following.
• 10A fuse [No. 19 located in the fuse block (J/B)]
• Harness for open or short between fuse and auto anti-dazzling inside mirror (homelink universal
transceiver).
2.
CHECK GROUND CIRCUIT
Check continuity between auto anti-dazzling inside mirror (homelink
universal transceiver) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair harness.
3.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
.
>> Inspection End.
Auto anti-dazzling inside mirror
(Homelink universal transceiver)
connector
Terminal Condition
Voltage (V)
(Approx.)
R7
10
Ground
Ignition switch position: LOCK
Battery voltage
ALKIA1245ZZ
Auto anti-dazzling inside mirror
(Homelink universal transceiver) connector
Terminal
Ground
Continuity
R7
3
Yes
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст