Nissan Pathfinder (2011 year). Instruction — part 20
PRECAUTIONS
ADP-145
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006247415
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000006247416
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
2011 Pathfinder
ADP-146
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
Precaution for Work
INFOID:0000000006822398
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components.
- Water soluble dirt: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the dirty
area.
Then rub with a soft and dry cloth.
- Oily dirt: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the dirty area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
• Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
• For genuine leather seats, use a genuine leather seat cleaner.
2011 Pathfinder
PREPARATION
ADP-147
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000008184909
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim tool set
Removing trim components
AWJIA0483ZZ
2011 Pathfinder
ADP-148
< REMOVAL AND INSTALLATION >
DRIVER SEAT CONTROL UNIT
REMOVAL AND INSTALLATION
DRIVER SEAT CONTROL UNIT
Removal and Installation
INFOID:0000000006247418
REMOVAL
1. Remove front driver seat. Refer to
SE-33, "Removal and Installation"
.
2. Disconnect the harness connector from the drivers seat control unit.
3. Remove the driver seat control unit.
INSTALLATION
Installation is in the reverse order of removal.
2011 Pathfinder
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
ADP-149
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
Removal and Installation
INFOID:0000000006247419
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1. Remove the battery negative terminal
PG-76, "Removal and Installation"
.
2. Remove the instrument lower panel LH using a suitable tool. Refer to
IP-12, "Removal and Installation"
.
3. Remove the screw (A).
4. Separate automatic drive positioner control unit (1) from bracket
and disconnect electrical connectors.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Clamp the harness in position.
NOTE:
After installing the automatic drive positioner control unit, perform additional service when disconnecting bat-
tery negative terminal. Refer to
ADP-10, "Special Repair Requirement"
.
ALIIA0210GB
2011 Pathfinder
ADP-150
< REMOVAL AND INSTALLATION >
SEAT MEMORY SWITCH
SEAT MEMORY SWITCH
Removal and Installation
INFOID:0000000006247420
Refer to
INT-15, "Removal and Installation"
for removal and installation of seat memory switch from the door
finisher.
2011 Pathfinder
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-151
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
Removal and Installation
INFOID:0000000006247421
Refer to
for removal and installation of door mirror remote control switch from instru-
ment lower panel LH.
2011 Pathfinder
ADP-152
< REMOVAL AND INSTALLATION >
PEDAL ADJUSTING MOTOR
PEDAL ADJUSTING MOTOR
Removal and Installation
INFOID:0000000006247422
The pedal adjusting motor is part of the accelerator pedal. Replace the pedal adjusting motor and accelerator
pedal as an assembly. Refer to
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст