Nissan Pathfinder (2011 year). Instruction — part 634
WHEEL AND TIRE ASSEMBLY
WT-51
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
4. If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top another.
5. Start balancer machine again.
6. Install balance weight on inner side of road wheel in the bal-
ancer machine indication position (angle).
CAUTION:
Do not install more than two balance weights.
7. Start balancer machine. Make sure that inner and outer residual
imbalance values are 5 g (0.17 oz) each or below.
8. If either residual imbalance value exceeds 5 g (0.17 oz), repeat installation procedures.
TIRE ROTATION
• Follow the maintenance schedule for tire rotation service intervals.
MA-11, "FOR USA AND CANADA : Introduction to Peri-
(United States and Canada), or
MEXICO : Periodic Maintenance Schedule"
(Mexico).
• When installing the wheel, tighten wheel nuts to the specified
torque.
CAUTION:
• Do not include the spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
• Use NISSAN genuine wheel nuts for aluminum wheels.
• Perform the ID registration, after tire rotation. Refer to
WT-6, "ID Registration Procedure"
Wheel balance
Dynamic (At flange)
Static (At flange)
Maximum allowable im-
balance
Refer to
.
PEIA0033E
Wheel nut tightening
torque
: 133 N·m (14 kg-m, 98 ft-lb)
SMA829C
2011 Pathfinder
WT-52
< UNIT REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
UNIT REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Transmitter (Pressure Sensor)
INFOID:0000000006246407
REMOVAL
1. Remove wheel and tire using power tool.
2. Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
3. Gently bounce tire so that transmitter falls to bottom of tire.
Place wheel and tire assembly on tire changing machine and
break both tire beads. Ensure that the transmitter remains at the
bottom of the tire while breaking the bead.
4. Turn tire so that valve hole is at bottom, and gently bounce the
tire to ensure transmitter is near valve hole. Carefully lift tire onto
turntable and position valve hole (and transmitter) 270 degrees
from mounting/dismounting head.
5. Lubricate the tire well with a suitable non-silicone lubricant, and
remove top side of tire. Reach inside the tire and remove the
transmitter.
CAUTION:
Do not use silicone lubricant. Use of silicone lubricant will
deteriorate the tire and wheel.
6. Remove the second side of the tire as normal.
INSTALLATION
1. Place first side of tire onto rim.
2. Apply a suitable non-silicone lubricant to new transmitter seal then install seal on transmitter.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
• Do not reuse seal.
SEIA0047E
WEIA0046E
SEIA0049E
2011 Pathfinder
REMOVAL AND INSTALLATION
WT-53
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3. Mount transmitter on rim and tighten nut at a maximum speed of
10 rpm.
NOTE:
Make sure no burrs exist in the valve stem hole of the wheel.
4. Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degrees from mounting/dismounting head.
NOTE:
Do not touch transmitter with mounting head.
5. Lubricate the tire well with a suitable non-silicone lubricant, and
install second side of tire as normal. Ensure that tire does not
rotate relative to rim.
CAUTION:
Do not use silicone lubricant. Use of silicone lubricant will
deteriorate the tire and wheel.
6. Inflate tire and balance the wheel and tire assembly. Refer to
7. Install wheel and tire assembly in appropriate wheel position on vehicle. Refer to
.
NOTE:
If replacing the transmitter, then transmitter wake up operation must be performed. Refer to
.
8. Adjust neutral position of steering angle sensor. Refer to
BRC-121, "ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
Transmitter nut
tightening torque
: 7.7 N·m (0.79 kg-m, 68 in-lb)
WEIA0137E
WEIA0046E
2011 Pathfinder
WT-54
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000006246408
Tire
INFOID:0000000006246409
Unit: kPa (kg/cm
2
, psi)
Wheel type
Aluminum
Steel
Inside
Outside
Maximum radial
runout limit
Lateral mm (in)
0.3 (0.012) or less
1.0 (0.039) or less
0.9 (0.035) or less
Radial mm (in)
0.3 (0.012) or less
0.8 (0.031) or less
0.4 (0.016) or less
Maximum allowable
imbalance
Dynamic (at rim flange)
Less than 5 g (0.18 oz) (per side)
Static (at rim flange)
Less than 10 g (0.35 oz)
Tire size
Air pressure
Conventional tire
Spare tire
P245/75R16
240 (2.4, 35)
240 (2.4, 35)
P265/70R16
240 (2.4, 35)
240 (2.4, 35)
P265/75R16
240 (2.4, 35)
240 (2.4, 35)
P265/65R17
240 (2.4, 35)
240 (2.4, 35)
P265/60R18
240 (2.4, 35)
240 (2.4, 35)
2011 Pathfinder
WW-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
WW
A
B
WW
N
O
P
CONTENTS
WIPER & WASHER
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
SYSTEM DESCRIPTION . . . . . . . ..
FRONT WIPER AND WASHER SYSTEM . . ..
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . ....
REAR WIPER AND WASHER SYSTEM . . .
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
WIPER . . . . . . . . . . . . . . . . . ...
WIPER : CONSULT-III Function (BCM - WIPER) .
DIAGNOSIS SYSTEM (IPDM E/R) . . . . . .
Diagnosis Description . . . . . . . . . . . .
CONSULT - III Function (IPDM E/R) . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
WIPER AND WASHER FUSE . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER MOTOR LO CIRCUIT . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER MOTOR HI CIRCUIT . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER AUTO STOP SIGNAL CIR-
CUIT . . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER MOTOR GROUND CIRCUIT ...
Diagnosis Procedure . . . . . . . . . . . ...
WASHER SWITCH . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
WASHER MOTOR CIRCUIT . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
REAR WIPER MOTOR CIRCUIT . . . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
REAR WIPER AUTO STOP SIGNAL CIRCUIT
...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . ..
BCM (BODY CONTROL MODULE) . . . . .
Reference Value . . . . . . . . . . . . . ..
Terminal Layout . . . . . . . . . . . . . ...
Physical Values . . . . . . . . . . . . . ...
Fail Safe . . . . . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ...
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) . . . .
Reference Value . . . . . . . . . . . . . ..
Terminal Layout . . . . . . . . . . . . . ...
Physical Values . . . . . . . . . . . . . ...
2011 Pathfinder
WW-2
Fail Safe . . . . . . . . . . . . . . . . .
DTC Index . . . . . . . . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . .
FRONT WIPER AND WASHER SYSTEM . . .
Wiring Diagram . . . . . . . . . . . . . ...
REAR WIPER AND WASHER SYSTEM . . ...
Wiring Diagram . . . . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . .
WIPER AND WASHER SYSTEM SYMPTOMS
...
Symptom Table . . . . . . . . . . . . . ..
NORMAL OPERATING CONDITION . . . .
Description . . . . . . . . . . . . . . . ..
FRONT WIPER DOES NOT OPERATE . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . .
PRECAUTION . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ..
FRONT WIPER AND WASHER SYSTEM . .
Removal and Installation . . . . . . . . . . .
Washer Nozzle Adjustment . . . . . . . . . .
REAR WIPER AND WASHER SYSTEM . . ...
Removal and Installation . . . . . . . . . . .
Rear Washer Nozzle Adjustment . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . ..
2011 Pathfinder
DIAGNOSIS AND REPAIR WORKFLOW
WW-3
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000006247886
DETAILED FLOW
1.
LISTEN TO CUSTOMER COMPLAINT
Listen to customer complaint. Get detailed information about the conditions and environment when the symp-
tom occurs.
>> GO TO 2
2.
VERIFY THE SYMPTOM WITH OPERATIONAL CHECK
Verify the symptom with operational check. Refer to
WW-13, "Diagnosis Description"
.
>> GO TO 3
3.
GO TO APPROPRIATE TROUBLE DIAGNOSIS
Go to appropriate trouble diagnosis. Refer to
.
>> GO TO 4
4.
REPAIR OR REPLACE
Repair or replace the specific parts.
>> GO TO 5
5.
FINAL CHECK
Final check.
Is inspection result normal?
YES
>> Inspection End.
NO
>> Refer to
GI-37, "Intermittent Incident"
.
2011 Pathfinder
WW-4
< SYSTEM DESCRIPTION >
FRONT WIPER AND WASHER SYSTEM
SYSTEM DESCRIPTION
FRONT WIPER AND WASHER SYSTEM
System Diagram
INFOID:0000000006247887
System Description
INFOID:0000000006247888
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER INT OPERATION (LINKED WITH VEHICLE SPEED)
ABLIA2789GB
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст