Nissan Pathfinder (2011 year). Instruction — part 603
TM-170
< REMOVAL AND INSTALLATION >
SHIFT CONTROL SYSTEM
REMOVAL AND INSTALLATION
SHIFT CONTROL SYSTEM
Exploded view
INFOID:0000000006244874
Removal and Installation
INFOID:0000000006244875
REMOVAL
1. Remove the center console. Refer to
IP-21, "Removal and Installation"
.
2. Disconnect the following from the shift selector assembly.
• A/T shift selector control cable
• A/T key interlock cable
• A/T shift selector connector
3. Remove the shift selector assembly.
INSTALLATION
1.
Shift selector handle
2.
Shift selector handle clip
3.
Shift selector handle cover
4.
A/T finisher
5.
Position lamp
6.
Position indicator
7.
A/T shift selector control cable
8.
Lock plate
9.
A/T key interlock cable
10. Shift selector assembly
Front
AWDIA0754GB
2011 Pathfinder
SHIFT CONTROL SYSTEM
TM-171
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Installation is in the reverse order of removal.
• Be sure to adjust shift selector cable. Refer to
TM-171, "Inspection and Adjustment"
Inspection and Adjustment
INFOID:0000000006244876
INSPECTION
With the shift selector in the “P” position, turn the ignition switch to the ON position with the engine OFF.
Confirm that the following conditions apply.
• The shift selector can be shifted from the “P” position only when the brake pedal is depressed.
• The shift selector stops at each position with the feel of engagement when it is moved through all the posi-
tions.
• There is no excessive effort, sticking, noise or rattle.
• The actual position of the shift selector matches the position shown by the shift position indicator and the A/
T body.
• The back-up lamps illuminate only when the shift selector is placed in the “R” position.
• The back-up lamps do not illuminate when the shift selector is pushed against the “R” position when in the
“P” or “N” position.
• The engine can only be started with the shift selector in the “P” and “N” positions.
• The A/T is locked completely when in the “P” position.
ADJUSTMENT
1. Loosen nut (A) of A/T shift selector control cable.
2. Place the instruction lever (B) and A/T shift selector in “P” position.
3. Push the shift selector control cable in the direction shown with a
force of 9.8 N (1kg, 2.2 lb), and release it, this is in the natural
state. Tighten A/T shift selector control cable nut (A) to specifica-
tions.
A/T shift selector
control cable nut
: 14.7 N·m (1.5 kg-m, 11 ft-lb)
AWDIA0755ZZ
2011 Pathfinder
TM-172
< REMOVAL AND INSTALLATION >
OIL PAN
OIL PAN
Removal and Installation
INFOID:0000000006244877
Removal
1. Drain A/T fluid. Refer to
TM-157, "Changing the A/T Fluid (ATF)"
.
2. Remove clips (1) (VK56DE engine models) and oil pan bolts.
•
Vehicle front
•
Oil pan bolts
• Drain plug (3)
3. Remove oil pan (2) and oil pan gasket.
4. Check for foreign materials in oil pan to help determine cause of malfunction. If the A/T fluid is very dark,
has some burned smell, or contains foreign particles then friction material (clutches, band) may need
replacement. A tacky film that will not wipe clean indicates varnish build up. Varnish can cause valves,
servo, and clutches to stick and can inhibit pump pressure.
CAUTION:
If friction material is detected, flush the transmission cooler after repair. Refer to
5. Remove magnets from oil pan.
Installation
1. Install the oil pan magnets as shown.
AWDIA0023ZZ
SCIA5200E
SCIA5200E
2011 Pathfinder
OIL PAN
TM-173
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Install the oil pan (2) with new oil pan gasket and clips (1)
(VK56DE engine models).
•
: Vehicle Front
•
: Oil pan bolts
• Drain plug (3)
CAUTION:
• Be sure the oil drain plug is located to the rear of the
transmission assembly.
• Before installing oil pan bolts, remove any traces of old
sealant from the sealing surfaces and threaded holes.
• Do not reuse old gasket, replace with a new one.
• Always replace the oil pan bolts as they are self-sealing.
• Partially install the oil pan bolts in a criss-cross pattern to prevent dislocation of the gasket.
3. Tighten oil pan bolts in numerical order as shown.
4. Install drain plug with new gasket to oil pan and tighten to speci-
fication.
CAUTION:
Do not reuse drain plug gasket.
5. Refill the A/T with fluid and check for fluid leakage. Refer to
TM-155, "Checking the A/T Fluid (ATF)"
.
AWDIA0023ZZ
Oil pan bolts
: 7.9 N·m (0.81 kg-m, 70 in-lb)
Drain plug
: 34 N·m (3.5 kg-m, 25 ft-lb)
SCIA4113E
2011 Pathfinder
TM-174
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
CONTROL VALVE WITH TCM
Removal and Installation
INFOID:0000000006244878
VQ40DE MODELS
VK56DE MODELS
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
O-ring
7.
Plug
8.
Oil pan gasket
9.
Oil pan bolts
10. Oil pan
11. Magnet
12. Drain plug
13. Drain plug gasket
14. Terminal cord assembly
15. O-ring
A.
For tightening torque, refer to "Installation"
AWDIA0890GB
2011 Pathfinder
CONTROL VALVE WITH TCM
TM-175
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION OF CONTROL VALVE WITH TCM
Removal
1. Disconnect negative battery terminal.
2. Drain A/T fluid. Refer to
TM-157, "Changing the A/T Fluid (ATF)"
.
3. Disconnect A/T assembly harness connector.
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
O-ring
7.
Plug
8.
Oil pan gasket
9.
Brackets
10. Oil pan bolt
11. Oil pan
12. Magnet
13. Drain plug
14. Drain plug gasket
15. Terminal cord assembly
16. O-ring
A.
For tightening torque, refer to "Installation"
AWDIA0886GB
2011 Pathfinder
TM-176
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
4. Remove snap ring from A/T assembly harness connector.
5. Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
6. Remove oil pan and oil pan gasket. Refer to
TM-172, "Removal and Installation"
.
7. Straighten terminal clip (
) to free the output speed sensor har-
ness.
8. Disconnect output speed sensor connector (1).
CAUTION:
Do not damage connector.
9. Remove bolts (A), (B) and (C) from control valve with TCM.
SCIA5021E
SCIA5022E
JSDIA1316ZZ
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
2011 Pathfinder
CONTROL VALVE WITH TCM
TM-177
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the instruction valve notch and
instruction plate height. Remove it vertically.
11. Remove plug (1) with bracket (2) from control valve with TCM.
•
:Bolt
12. Remove the bracket (1) from plug (2).
13. Remove O-ring (1) from plug (2).
CAUTION:
Do not reuse O-ring.
SCIA5142E
JSDIA1311ZZ
JSDIA1312ZZ
JSDIA1313ZZ
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст