Nissan Pathfinder (2011 year). Instruction — part 130
ENGINE COOLANT
CO-11
< PERIODIC MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
PERIODIC MAINTENANCE
ENGINE COOLANT
System Inspection
INFOID:0000000006247850
WARNING:
• Never remove the radiator/reservoir cap when the engine is hot. Serious burns could occur from
high pressure fluid escaping from the radiator or reservoir.
• Wrap a thick cloth around the cap. Slowly push down and turn it a quarter turn to allow built-up pres-
sure to escape. Carefully remove the cap by pushing down and turning it all the way.
CHECKING COOLING SYSTEM HOSES
Check hoses for the following:
• Improper attachment
• Leaks
• Cracks
• Damage
• Loose connections
• Chafing
• Deterioration
CHECKING RESERVOIR LEVEL
• Check if the engine coolant reservoir tank level is within MIN to
MAX when the engine is cool.
• Adjust engine coolant level as necessary.
CHECKING COOLING SYSTEM FOR LEAKS
WARNING:
Never remove the radiator/reservoir cap when the engine is hot. Serious burns could occur from high
pressure coolant escaping from the radiator or reservoir.
• To check for leakage, apply pressure to the cooling system at the
reservoir filler neck using suitable tool and Tool.
CAUTION:
Higher pressure than specified may cause radiator damage.
NOTE:
In case that engine coolant decreases, replenish cooling system
with engine coolant.
• If any concerns are found, repair or replace damaged parts.
CHECKING RESERVOIR CAP
1. Inspect the reservoir cap.
• Replace the cap if the metal plunger cannot be seen around the edge of the black rubber gasket.
• Replace the cap if deposits of waxy residue or other foreign material are on the black rubber gasket or
the metal retainer.
NOTE:
Thoroughly wipe out the reservoir filler neck to remove any waxy residue or foreign material.
SMA412B
Tool number
: EG17650301 (J-33984-A)
Testing pressure : 137 kPa (1.4 kg/cm
2
, 20 psi)
WBIA0612E
2011 Pathfinder
CO-12
< PERIODIC MAINTENANCE >
[VQ40DE]
ENGINE COOLANT
2. Pull the negative-pressure valve to open it and check that it
closes completely when released.
• Check that there is no dirt or damage on the valve seat of the
reservoir cap negative-pressure valve.
• Check that there are no abnormalities in the opening and clos-
ing conditions of the negative-pressure valve.
3. Check reservoir cap relief pressure using suitable tool and Tool.
NOTE:
• Apply engine coolant to the cap seal surface.
• Replace the reservoir cap if there is any damage in the nega-
tive-pressure valve, or if the open-valve pressure is outside of
the limit.
CHECKING RADIATOR CAP
• Check valve seat of radiator cap.
- Replace the cap if the metal plunger cannot be seen around the
edge of the black rubber gasket.
- Replace the cap if deposits of waxy residue or other foreign mate-
rial are on the black rubber gasket or the metal retainer.
• Pull the negative-pressure valve to open it and check that it closes
completely when released.
- Check that there is no dirt or damage on the valve seat of the radi-
ator cap negative-pressure valve.
- Make sure that the valve operates properly while opening and
closing.
SMA967B
Tool number
: EG17650301 (J-33984-A)
Standard: 98 – 118 kPa (1.0 – 1.2 kg/cm
2
, 14 – 17 psi)
WBIA0570E
PBIC2816E
SMA967B
2011 Pathfinder
ENGINE COOLANT
CO-13
< PERIODIC MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
• Check radiator cap relief pressure using suitable tool and Tool.
- When connecting the radiator cap to the tester, apply water or coolant to the cap seal surface.
- Replace radiator cap if there is an abnormality in the negative-pressure valve, or if the open-valve pressure
is outside of the standard values.
• Replace the radiator cap if it exceeds the specifications in the above tests.
CAUTION:
When installing the radiator cap, thoroughly wipe out the radiator filler neck to remove waxy residue
or foreign material.
CHECKING RADIATOR
Check radiator for mud or clogging. If necessary, clean radiator as follows.
CAUTION:
• Be careful not to bend or damage the radiator fins.
• When radiator is cleaned without removal, remove all surrounding parts such as cooling fan, radia-
tor shroud and horns. Then tape the harness and electrical connectors to prevent water from enter-
ing.
1. Spray water to the back side of the radiator core using a side to side motion from the top down.
2. Stop spraying when debris no longer flows from radiator core.
3. Blow air into the back side of radiator core using a side to side motion from the top down.
• Use compressed air lower than 490 kPa (5 kg/cm
2
, 71 psi) and keep distance more than 30 cm (11.8 in).
4. Continue to blow air until no water sprays out.
5. Check for coolant leaks. Repair as necessary.
Changing Engine Coolant
INFOID:0000000006247851
WARNING:
• To avoid being scalded, never change the coolant when the engine is hot.
• Wrap a thick cloth around the cap to carefully remove the cap. First, turn the cap a quarter of a turn
to release any built-up pressure, then push down and turn the cap all the way to remove it.
DRAINING ENGINE COOLANT
1. Turn ignition switch ON and set temperature control lever all the way to HOT position or the highest tem-
perature position. Wait 10 seconds and turn ignition switch OFF.
2. Remove the engine under cover using power tool.
3. Open the radiator drain plug at the bottom of the radiator, and
remove the reservoir cap. This is the only step required when
partially draining the cooling system (radiator only).
CAUTION:
• Perform this step when the engine is cold.
• Do not allow the coolant to contact the drive belts.
Tool number
: EG17650301 (J-33984-A)
Standard: 98 – 118 kPa (1.0 – 1.2 kg/cm
2
, 14 – 17 psi)
WBIA0570E
LLIA0070E
2011 Pathfinder
CO-14
< PERIODIC MAINTENANCE >
[VQ40DE]
ENGINE COOLANT
4. When draining all of the coolant in the system for engine
removal or repair, it is necessary to drain the cylinder block.
Remove the cylinder block drain plugs (A), (B), (C), (D) and
block heater if equipped, to drain the cylinder block as shown.
CAUTION:
Do not reuse copper sealing washers.
NOTE:
For Canada, the (D) cylinder block drain plug as shown, is not a
cylinder block drain plug but a block heater.
5. Remove the reservoir tank to drain the engine coolant, then clean the reservoir tank before installing it.
6. Check the drained coolant for contaminants such as rust, corrosion or discoloration.
If the coolant is contaminated, flush the engine cooling system. Refer to
.
REFILLING ENGINE COOLANT
1. Close the radiator drain plug. Install the reservoir tank, cylinder
block drain plugs (A), (B), (C), (D) and block heater if equipped,
if removed for a total system drain or for engine removal or
repair.
• The radiator must be completely empty of coolant and water.
• Apply sealant to the threads of the cylinder block drain plugs
(A), (B), (C), (D). Use Genuine High Performance Thread
Sealant or equivalent. Refer to
.
CAUTION:
Do not reuse copper sealing washers.
Block Plug and Block Heater Installation
WLIA0020E
WLIA0020E
Part
Washer
Tightening Torque
A
No
Refer to
EM-106, "Disassembly and Assembly"
B
Reuse
No
Refer to
EM-106, "Disassembly and Assembly"
New
Refer to
EM-106, "Disassembly and Assembly"
2011 Pathfinder
ENGINE COOLANT
CO-15
< PERIODIC MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
2. Set the vehicle heater controls to the full HOT and heater ON position. Turn the vehicle ignition ON with
the engine OFF as necessary to activate the heater mode.
3. Remove the vented reservoir cap and replace it with a non-vented reservoir cap before filling the cooling
system.
4. Install the Tool by installing the radiator cap adapter onto the
radiator neck opening. Then attach the gauge body assembly
with the refill tube and the venturi assembly to the radiator cap
adapter.
5. Insert the refill hose into the coolant mixture container that is
placed at floor level. Make sure the ball valve is in the closed
position.
• Use recommended coolant or equivalent.
Refer to
MA-18, "FOR USA AND CANADA : Fluids and Lubri-
(United States and Canada),
(Mexico).
CAUTION:
Never use any cooling system additives such as radiator
sealer. Additives may clog the cooling system and cause
damage to the engine, transmission and/or cooling system.
6. Install an air hose to the venturi assembly, the air pressure must be within specification.
CAUTION:
The compressed air supply must be equipped with an air dryer.
7. The vacuum gauge will begin to rise and there will be an audible hissing noise. During this process open
the ball valve on the refill hose slightly. Rising coolant will be visible in the refill hose. After the refill hose is
full of coolant, close the ball valve. This will purge air trapped in the refill hose.
8. Continue to draw the vacuum until the gauge reaches 28 inches
of vacuum. The gauge may not reach 28 inches in high altitude
locations. Refer to the following table for expected vacuum read-
ings.
C
Yes
EM-106, "Disassembly and Assembly"
.
D
Plug
Yes
EM-106, "Disassembly and Assembly"
.
Block heater
EM-106, "Disassembly and Assembly"
.
Part
Washer
Tightening Torque
Tool number
: KV991J0070 (J-45695)
Cooling system capacity
(with reservoir)
: Refer to
USA AND CANADA : Flu-
ids and Lubricants"
ed States and Canada),
MA-20, "FOR MEXICO :
Fluids and Lubricants"
(Mexico).
Compressed air
supply pressure
: 549 - 824 kPa (5.6 - 8.4 kg/cm
2
,
80 - 119 psi)
LLIA0058E
Altitude above sea level
Vacuum gauge reading
0 - 100 m (328 ft)
: 28 inches of vacuum
300 m (984 ft)
: 27 inches of vacuum
500 m (1,641 ft)
: 26 inches of vacuum
1,000 m (3,281 ft)
: 24 - 25 inches of vacuum
LLIA0057E
2011 Pathfinder
CO-16
< PERIODIC MAINTENANCE >
[VQ40DE]
ENGINE COOLANT
9. When the vacuum gauge has reached the specified amount, disconnect the air hose and wait 20 seconds
to see if the system loses vacuum. If the vacuum level drops, perform necessary repairs to the system
and repeat steps 6 - 8 to bring the vacuum to the specified amount. Recheck for leaks.
10. Place the coolant container (with the refill hose inserted) at the same level as the top of the radiator. Then
open the ball valve on the refill hose so the coolant will be drawn up to fill the cooling system. The cooling
system is full when the vacuum gauge reads zero.
CAUTION:
Do not allow the coolant container to get too low when filling, to avoid air from being drawn into
the cooling system.
11. Remove the Tool from the radiator neck opening and install the radiator cap.
12. Remove the non-vented reservoir cap.
13. Fill the cooling system reservoir tank to the specified level. Run the engine to warm up the cooling system
and top up the system as necessary before installing the vented reservoir cap.
14. Install the engine under cover. Refer to
EXT-15, "Removal and Installation"
FLUSHING COOLING SYSTEM
1. Drain the water from the engine cooling system. Refer to
CO-13, "Changing Engine Coolant"
.
2. Fill the radiator and the reservoir tank (to the “MAX” line), with water. Reinstall the radiator cap and leave
the vented reservoir cap off.
3. Run the engine until it reaches normal operating temperature.
4. Press the engine accelerator two or three times under no-load.
5. Stop the engine and wait until it cools down.
6. Drain the water from the engine cooling system. Refer to
CO-13, "Changing Engine Coolant"
.
7. Repeat steps 2 through 6 until clear water begins to drain from the radiator.
2011 Pathfinder
RADIATOR
CO-17
< PERIODIC MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
RADIATOR
Checking Radiator
INFOID:0000000008191814
Check radiator for mud or clogging. If necessary, clean radiator as follows.
CAUTION:
• Be careful not to bend or damage the radiator fins.
• When radiator is cleaned without removal, remove all surrounding parts such as cooling fan shroud
and horns. Then tape the harness and electrical connectors to prevent water from entering.
1. Spray water to the back side of the radiator core using a side to side motion from the top down.
2. Stop spraying when debris no longer flows from radiator core.
3. Blow air into the back side of radiator core using a side to side motion from the top down.
• Use compressed air lower than 490 kPa (5 kg/cm
2
, 71 psi) and keep distance more than 30 cm (11.8 in).
4. Continue to blow air until no water sprays out.
5. Check for coolant leaks. Repair as necessary.
2011 Pathfinder
CO-18
< REMOVAL AND INSTALLATION >
[VQ40DE]
RADIATOR
REMOVAL AND INSTALLATION
RADIATOR
Exploded View
INFOID:0000000006247852
Removal and Installation
INFOID:0000000006247853
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter
of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove engine under cover. Refer to
EXT-15, "Removal and Installation"
2. Drain engine coolant from radiator. Refer to
1.
Upper mount bracket
2.
Mounting rubber (upper)
3.
Radiator cap
4.
Radiator
5.
Mounting rubber (lower)
6.
A/T fluid cooler hose
7.
A/T fluid cooler hose
8.
O-ring
9.
Drain plug
10. Cooling fan assembly
11. Radiator shroud (upper)
12. Radiator hose (lower)
13. Radiator shroud (lower)
14. Reservoir tank hose
15. Reservoir tank cap
16. Reservoir tank
17. Water hose
18. Radiator hose (upper)
A.
To heater return tube
B.
To water pipe
C.
To A/T cooler tube
D.
To water inlet and thermostat assembly
Vehicle front
PBIC3861E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст